SOR/2010-9020104
29
20251
23
MOTOR VEHICLE SAFETY ACTMotor Vehicle Restraint Systems and Booster Seats Safety RegulationsP.C.2010-54520104
29
Whereas, pursuant to subsection 11(3) of the Motor Vehicle Safety Acta, a copy of the proposed Motor Vehicle Restraint Systems and Booster Seats Safety Regulations, substantially in the annexed form, was published in the Canada Gazette, Part I, on October 10, 2009, and a reasonable opportunity was afforded to interested persons to make representations to the Minister of Transport with respect to the proposed Regulations;S.C. 1993, c. 16Therefore, Her Excellency the Governor General in Council, on the recommendation of the Minister of Transport pursuant to subsection 11(1) of the Motor Vehicle Safety Acta, hereby makes the annexed Motor Vehicle Restraint Systems and Booster Seats Safety Regulations.GeneralInterpretation
DefinitionsThe following definitions apply in these Regulations.Act means the Motor Vehicle Safety Act. (Loi)booster seat means a removable device designed to be used in a vehicle for seating a person whose mass is at least 18 kg, to ensure that the seat belt assembly fits properly. (siège d’appoint)car bed means a restraint system for an infant with special needs that is designed to restrain the infant in a supine or prone position on a continuous flat surface.  (lit d’auto)child means a person whose mass is more than 10 kg and not more than 30 kg.  (enfant)CMVSS means Canada Motor Vehicle Safety Standard.  (NSVAC)custom restraint system for a disabled person means a restraint system, other than a mass-produced restraint system, designed for a specific disabled person. (ensemble de retenue sur mesure pour personne handicapée)disabled person means a person, other than an infant with special needs, who, for orthopaedic reasons or because of the person’s build or other physical characteristics, is unable to use an infant restraint system, a child restraint system, a booster seat, a built-in device referred to in item 213.4 of Schedule III to the Motor Vehicle Safety Regulations, or a vehicle seat belt. (personne handicapée)infant means a person who is unable to walk unassisted and whose mass is not more than 10 kg.  (bébé)infant with special needs means an infant who is unable to use an infant restraint system andwho was born at less than 37 weeks’ gestation;whose mass at birth was less than 2.2 kg; orwho has special breathing needs. (bébé qui a des besoins spéciaux)lower connector system means a system consisting of two connectors that each fit inside a checking device having the envelope dimensions shown in Figure 9 of Schedule 7, that are attached to the lower part of a restraint system or booster seat in a manner that does not allow for their removal without the use of tools, and that allow the restraint system or booster seat to be securely attached to a lower universal anchorage system of a vehicle.  (système d’attaches inférieures)lower universal anchorage system means a device, other than a vehicle seat belt, that is designed to secure the lower portion of a restraint system or booster seat to a vehicle, and that transfers the load from the restraint system or booster seat and its occupant to the vehicle structure or a vehicle seat structure. (dispositif universel d’ancrages d’attaches inférieurs)mass-produced means manufactured, in whatever quantity, using only standard or uniform parts. (fabriqué en série)restraint system means a removable device designed to be used together with the seat of a vehicle in order to restraint an infant, an infant with special needs, a child or a disabled person, but does not include a booster seat or a vehicle seat belt.  (ensemble de retenue)seat orientation reference line or SORL means the horizontal line passing through the plane of symmetry of the standard seat assembly and passing through the Z point as shown in Figures 3 and 4 of Schedule 7. (ligne repère d’orientation du siège ou LROS)standard seat assembly means the seat that is specified in the drawing package entitled Standard Seat Assembly Specifications for Motor Vehicle Restraint Systems and Booster Seats Safety Regulations Compliance Testing (January 1, 2010), published by the Department of Transport, and that has seat belt anchorage points and a lower universal anchorage system located as indicated in Figures 3 and 4 of Schedule 7, respectively. (siège normalisé)tether strap means a device that is fitted with a tether strap hook and secured to the rigid structure of a restraint system or booster seat, and that transfers the load from the restraint system or booster seat and its occupant to the user-ready tether anchorage. (courroie d’attache)tether strap hook means a device that is used to attach a tether strap to a user-ready tether anchorage and that has an interface profile shown in Figure 1 of Schedule 7 or, in the case of a device with integrated adjustment hardware, Figure 2 of Schedule 7.  (crochet de la courroie d’attache)torso means the portion of the body of an anthropomorphic test device or an occupant, excluding the thighs, that when the device or occupant is seated in a restraint system other than a car bed or in a booster seat, lies between the top of the restraint system seating surface or booster seat seating surface and the top of the shoulders; orwhen the device or occupant is seated in a car bed, lies between the top of the continuous flat surface of the car bed and the top of the shoulders. (torse)TSD 209 means Technical Standards Document No. 209, Seat Belt Assemblies, published by the Department of Transport, as amended from time to time. (DNT 209)TSD 302 means Technical Standards Document No. 302, Flammability of Interior Materials, published by the Department of Transport, as amended from time to time. (DNT 302)user-ready tether anchorage means a device that transfers the tether strap load from a restraint system or booster seat and its occupant to the vehicle structure or a vehicle seat structure, and that is designed to accept a tether strap hook directly, without requiring the installation of any other device. (ancrage d’attache prêt à utiliser)[Repealed, SOR/2014-307, s. 31]Classes of vehiclesIn these Regulations, “classes of vehicles” refers to those classes of vehicles prescribed by section 4 of the Motor Vehicle Safety Regulations and set out in Schedule III to those Regulations.Interpretation — restraint system or booster seatFor the purposes of these Regulations, a reference in TSD 209 to webbing, a belt buckle, a tether strap attachment or a related piece of adjustment hardware that is part of a Type 1 seat belt assembly is to be read as a reference to webbing, a belt buckle, a tether strap attachment or a related piece of adjustment hardware that is part of a restraint system or booster seat, as the case may be.SOR/2013-117, s. 12; SOR/2014-307, s. 31
National Safety Mark
National Safety MarkFor the purposes these Regulations, the symbol set out in Schedule 2 is prescribed as the national safety mark.Authorization by MinisterFor the purposes of subsection 3(2) of the Act, on application by a company, the Minister may, in the form set out in Schedule 1, authorize the company to apply the national safety mark to a restraint system or booster seat and to any accompanying documentation or any packaging.Application for authorizationA company that intends to apply the national safety mark to a restraint system or booster seat must apply to the Minister to obtain the authorization referred to in subsection (1.1).National safety markA company that applies the national safety mark to a restraint system or booster seat must reproduce the national safety mark as shown in Schedule 2, including the following information, in the locations indicated in that schedule:the authorization number assigned to the company by the Minister; andthe number or numbers of the CMVSS to which the restraint system or booster seat conforms, namely,213, in the case of a child restraint system,213.1, in the case of an infant restraint system,213.2, in the case of a booster seat,213.3, in the case of a mass-produced restraint system for disabled persons,213.3, in the case of a custom restraint system for a disabled person that is designed to be used only in school buses, and213.5, in the case of a restraint system for infants with special needs.IdemThe national safety mark must be at least 50 mm in diameter and be stitched onto the restraint system or booster seat, indelibly moulded into or onto it, or indelibly printed on a label affixed to it in a permanent manner.Visibility of national safety markThe national safety mark must, when applied to a restraint system or booster seat, be fully visible.Location of national safety mark — removable baseIf a restraint system is manufactured with a removable base and the seating component of the restraint system is designed to be used in a vehicle with or without the base, the national safety mark must be applied to the seating component.SOR/2020-22, s. 18
Prescribed Classes of Equipment
Prescribed classes of equipmentFor the purposes of sections 4 and 5 of the Act, child restraint systems, infant restraint systems, booster seats, restraint systems for disabled persons and restraint systems for infants with special needs are prescribed classes of equipment.SOR/2013-117, s. 13SOR/2020-22, s. 19
Prescribed Standards
CVMSS 213Every child restraint system must conform to the applicable standards set out in Part 2, CMVSS 213 — Child Restraint Systems.CVMSS 213.1Every infant restraint system must conform to the applicable standards set out in Part 3, CMVSS 213.1 — Infant Restraint Systems.CVMSS 213.2Every booster seat must conform to the applicable standards set out in Part 4, CMVSS 213.2 — Booster Seats.CVMSS 213.3Every restraint system for disabled persons must conform to the applicable standards set out in Part 5, CMVSS 213.3 — Restraint Systems for Disabled Persons.CVMSS 213.5Every restraint system for infants with special needs must conform to the applicable standards set out in Part 6, CMVSS 213.5 — Restraint Systems for Infants with Special Needs.Applicable CVMSSEvery restraint system that is designed to be used as more than one type of restraint system or as a restraint system and booster seat must conform to the standards set out in Parts 2 to 6 that are applicable to each type of restraint system or booster seat for which it is designed to be used.
Restraint System and Booster Seat InformationNational Safety Mark
No importation without national safety markA company must not import into Canada a restraint system other than a custom restraint system for a disabled person that is not designed to be used only in school buses, or a booster seat, unless the company has applied the national safety mark to the restraint system or booster seat.
Lower Universal Anchorage System Symbol
Lower universal anchorage system symbolEvery restraint system or booster seat that is equipped with a lower connector system must bear the lower universal anchorage system symbol shown in Schedule 3, on a background of contrasting colour, on or near the lower connector system, and the symbol must be fully visible to a person installing the restraint system or booster seat when the restraint system or booster seat is positioned in the vehicle.
Records
RecordsA company must maintain — for each restraint system or booster seat to which it applies the national safety mark or that it imports into Canada — the records referred to in paragraph 5(1)(g) of the Act and retain those records, in paper form or in readily readable electronic form, for a period of at least five years after the day on which the restraint system or booster seat is manufactured or imported.IdemIf the records referred to in subsection (1) are maintained by a person on behalf of the company, the company must keep the name and address of the person.Request from inspectorOn request in writing from an inspector, a company must send to that inspector a copy, in either official language, of the records referred to in subsection (1) within30 working days after day on which the request is mailed; orif the records must be translated, 45 working days after the day on which the request is mailed.SOR/2019-253, s. 4
Registration Systems
Information cardFor the purpose of maintaining the registration system referred to in paragraph 5(1)(h) of the Act, a company must provide to each person who purchases a restraint system or booster seat an information card, in both official languages, thatpermits the purchaser to provide to the company or to a duly authorized representative of the company, at no cost, the purchaser’s name, mailing address and email address, the model name and number of the restraint system or booster seat, the date of purchase and the date of manufacture; andincludes a safety message concerning the importance of providing the information.Information to be included in registration systemThe registration system maintained by a company in accordance with paragraph 5(1)(h) of the Act must consist of the information provided to the company under paragraph (1)(a), and that information must be used only for the purposes of paragraph 5(1)(h) of the Act.Minimum retention periodThe information in the registration system maintained by a company in relation to a restraint system or booster seat must be kept for at least five years after the day on which the restraint system or booster seat is purchased.
ImportationGeneral
DeclarationFor the purposes of paragraph 5(1)(b) of the Act, a company that imports into Canada a restraint system or booster seat must make, at the nearest customs office that is open for business, a declaration signed by the company’s duly authorized representative that contains the following information:the name of the manufacturer of the restraint system or booster seat;the name and address of the company importing the restraint system or booster seat;[Repealed, SOR/2013-117, s. 14]a statement from the manufacturer or its duly authorized representative that the restraint system or booster seat conforms to the prescribed standards applicable on the date of manufacture;the model name and number of the restraint system or booster seat;the number of restraint systems and the number of booster seats imported at the same time; andthe date on which the restraint system or booster seat was imported.SOR/2013-117, s. 14
Temporary Importation
Prescribed purposesFor the purposes of paragraph 7(1)(a) of the Act, the prescribed purposes for which a restraint system or booster seat may be imported temporarily are the following:exhibition;demonstration;evaluation;testing; andfurther manufacturing prior to export.DeclarationThe declaration referred to in paragraph 7(1)(a) of the Act must be filed with the Minister, be signed by the person importing the restraint system or booster seat and contain the following information:the name of the manufacturer of the restraint system or booster seat;the importer’s name, mailing address, telephone number, facsimile number and email address and, if the importer is a company, the contact information of a contact person at the company;the make and the model name or number of the restraint system or booster seat;the date on which the restraint system or booster seat is to be presented for importation;the purpose for which the restraint system or booster seat is being imported and a statement that it will be used only for that purpose;a statement indicating that the restraint system or booster seat will remain in Canada for a period of not more than one year or the period specified by the Minister, as applicable;a statement indicating that the restraint system or booster seat will be exported or destroyed before the end of the one-year period or the period specified by the Minister, as applicable; andif the declaration is signed by a representative, a statement by the importer indicating that the representative is authorized to sign.SOR/2020-22, s. 20
Notice of Defect
Prescribed personFor the purposes of subsection 10(1) of the Act, a person, other than the first retail purchaser, who obtained a restraint system or booster seat from a company is a prescribed person.Form and languageA notice of defect that is required to be given under subsection 10(1) of the Act must be in writing, in either paper or electronic form, andin the case of a notice given to the Minister, be in either official language; andin the case of a notice given to the current owner of the restraint system or booster seat or a prescribed person,be in the person’s official language of choice, if it is known, orbe in both official languages.PeriodA company must give the notice of defect to the current owner of the restraint system or booster seat and to the prescribed person as soon as feasible, but not later than 60 days after the day on which the company gives the notice of defect to the Minister.Notice to Minister — contentThe notice of defect that is given to the Minister must contain the following information:the company’s name and its contact information for the purpose of correspondence;the name of the manufacturer of the restraint system or booster seat;the number, title or other identification that is assigned by the company to the notice;for each restraint system or booster seat that may contain the defect, its model name and number, the prescribed class of equipment and any other information that is necessary to permit its identification;the period during which the restraint systems or booster seats were manufactured;the estimated number of restraint systems or booster seats that could potentially contain the defect;the estimated percentage of the restraint systems or booster seats referred to in paragraph (f) that contain the defect;a description of the nature of the defect, including the causes and contributing factors, if known, and a description of the location of the defect;the systems or components of the restraint system or booster seat that may be affected by the defect;a chronology of the principal events that led to the determination of the existence of the defect;all relevant information, including a summary of warranty claims, field reports and service reports, with their dates of receipt, that the company used to determine the existence of the defect;a description of the safety risk to persons arising from the defect;a description of the corrective measures to be taken in respect of the defect and how they are to be implemented;any precautions that may be taken to minimize the safety risk until the corrective measures are implemented; andthe estimated date on which the notice of defect will be sent to the current owner of the restraint system or booster seat and the estimated date on which the notice of defect will be sent to a prescribed person.Unavailable informationThe company is not required to provide the Minister with the information referred to in paragraphs (4)(j), (k), (m) and (n) if it is not available on the day on which the notice is given but must provide that information as soon as it is available.Notice to owner — contentA notice of defect that is given to the current owner of the restraint system or booster seat must contain the following information:the company’s name;the model name and number of the restraint system or booster seat;the following statements:“This notice is sent to you in accordance with the requirements of the Motor Vehicle Safety Act.”, and“This is to inform you that your restraint system or booster seat may contain a defect that could affect the safety of a person.”;the number, title or other identification that is assigned by the company to the notice;the motor vehicle safety recall number that is issued by the Department of Transport;a description of the nature of the defect, including the causes, and a description of the location of the defect;the systems or components of the restraint system or booster seat that may be affected by the defect;operating conditions or other factors that may cause a malfunction of the system or component of the restraint system or booster seat;the warning signs, if any, of any malfunction that could arise as a result of the defect;a description of the safety risk to persons arising from the defect;the type of injury that may result from the defect;a description of the corrective measures to be taken in respect of the defect and how they are to be implemented, includinga general description of the work involved,the estimated time required in order to take the corrective measures,a statement that the company will cover the costs of the corrective measures or an estimate of the cost of the corrective measures to the current owner of the restraint system or booster seat, andinformation identifying the persons who can implement the corrective measures; andany precautions that may be taken to minimize the safety risk until the corrective measures are implemented.Unavailable informationThe company is not required to provide the current owner with the information referred to in paragraph (6)(l) if it is not available on the day on which the notice is given but must provide that informationas soon as it is available; orat the same time as the company provides the information required under subsection 10.4(1) of the Act.Required wordingThe words “SAFETY”,  “RECALL”, “RAPPEL” and “SÉCURITÉ” are required to be clearly visibleon the envelope, or through a window of the envelope, in upper case and in a font size that is larger than the one used for the recipient’s address, if the notice of defect is given to the current owner in paper form; orin the subject line of the communication, in upper case, if the notice of defect is given to the current owner in electronic form.Notice to prescribed person — contentA notice of defect that is given to a prescribed person must contain the following information:the company’s name;for each restraint system or booster seat that may contain the defect, its model name and number and any other information that is necessary to permit its identification;the number, title or other identification that is assigned by the company to the notice;the motor vehicle safety recall number issued by the Department of Transport;a description of the nature of the defect, including the causes, and a description of the location of the defect;operating conditions or other factors that may cause a malfunction of the system or component of the restraint system or booster seat;a description of the safety risk to persons arising from the defect;a description of the corrective measures to be taken in respect of the defect and how they are to be implemented; andany precautions that may be taken to minimize the safety risk until the corrective measures are implemented.Unavailable informationThe company is not required to provide the prescribed person with the information referred to in paragraph (9)(h) if it is not available on the day on which the notice is given but must provide that information as soon as it is available.SOR/2013-117, s. 15; SOR/2015-111, s. 3SOR/2019-253, s. 5
Notice of Non-compliance
Prescribed personFor the purposes of subsection 10.1(1) of the Act, a person, other than the first retail purchaser, who obtained a restraint system or booster seat from a company is a prescribed person.Form and LanguageA notice of non-compliance that is required to be given under subsection 10.1(1) of the Act must be in writing, in either paper or electronic form, andin the case of a notice given to the Minister, be in either official language; andin the case of a notice given to the current owner of the restraint system or booster seat or a prescribed person,be in the person’s official language of choice, if it is known, orbe in both official languages.PeriodUnless the notice of non-compliance contains a statement under subparagraph (4)(k)(i), a company must give the notice of non-compliance to the current owner of the restraint system or booster seat and to the prescribed person as soon as feasible, but not later than 60 days after the day on which the company gives the notice of non-compliance to the Minister.Period — statement deniedIf the notice of non-compliance contains a statement under subparagraph (4)(k)(i) and the Minister advises the company that the Minister has determined that the non-compliance is not inconsequential to safety, the company must give the notice of non-compliance to the current owner of the restraint system or booster seat and to the prescribed person as soon as feasible after the day on which the company receives the Minister’s determination, but not later than 60 days after that day.Notice to Minister — contentA notice of non-compliance that is given to the Minister must contain the following information:the company’s name and its contact information for the purpose of correspondence;the name of the manufacturer of the restraint system or booster seat;the number, title or other identification that is assigned by the company to the notice;for each restraint system or booster seat that may be non-compliant, the model name and number, the prescribed class of equipment and any other information that is necessary to permit its identification;the period during which the restraint systems or booster seats were manufactured;the estimated number of restraint systems or booster seats that could potentially be non-compliant;the estimated percentage of the restraint systems or booster seats referred to in paragraph (f) that are non-compliant;a description of the non-compliance, including the applicable regulatory requirement, the causes and contributing factors, if known;the systems or components of the restraint system or booster seat that may be affected by the non-compliance;a chronology of the principal events that led to the determination of the non-compliance, including the test results, observations, inspections and any other relevant information;as the case may be,a statement that the non-compliance is inconsequential to safety, including detailed information to support the statement, ora description of the safety risk to persons arising from the non-compliance;a description of the corrective measures to be taken in respect of the non-compliance and how they are to be implemented;any precautions that may be taken to minimize the safety risk until the corrective measures are implemented; andthe estimated date on which the notice of non-compliance will be sent to the current owner of the restraint system or booster seat and the estimated date on which the notice of non-compliance will be sent to a prescribed person.Unavailable informationThe company is not required to provide the Minister with the information referred to in paragraphs (4)(j), (l) and (m) if it is not available on the day on which the notice is given but must provide that information as soon as it is available.Information referred to in paragraph (4)(n)The company is not required to provide the Minister with the information referred to in paragraph (4)(n) if the notice of non-compliance contains a statement under subparagraph (4)(k)(i), but if the Minister advises the company that the Minister has determined that the non-compliance is not inconsequential to safety, the company must provide that information within five working days after the day on which the company receives the Minister’s determination.Notice to owner — contentA notice of non-compliance that is given to the current owner of the restraint system or booster seat must contain the following information:the company’s name;the model name and number of the restraint system or booster seat;the following statements:“This notice is sent to you in accordance with the requirements of the Motor Vehicle Safety Act.”, and“This is to inform you that your restraint system or booster seat may be non-compliant with the requirements of the Motor Vehicle Restraint Systems and Booster Seats Safety Regulations and that the non-compliance could affect the safety of a person.”;the number, title or other identification that is assigned by the company to the notice;the motor vehicle safety recall number that is issued by the Department of Transport;a description of the non-compliance, including the causes;the systems or components of the restraint system or booster seat that may be affected by the non-compliance;operating conditions or other factors that may cause a malfunction of the system or component of the restraint system or booster seat;the warning signs, if any, of any malfunction that could arise as a result of the non-compliance;a description of the safety risk to persons arising from the non-compliance, if any;the type of injury that may result from the non-compliance;a description of the corrective measures to be taken in respect of the non-compliance and how they are to be implemented, includinga general description of the work involved,the estimated time required in order to take the corrective measures,a statement that the company will cover the costs of the corrective measures or an estimate of the cost of the corrective measures to the current owner of the restraint system or booster seat, andinformation identifying the persons who can implement the corrective measures; andany precautions that may be taken to minimize the safety risk until the corrective measures are implemented.Unavailable informationThe company is not required to provide to the current owner the information referred to in paragraph (6)(l) if it is not available on the day on which the notice is given but must provide that informationas soon as it is available; orat the same time as the company provides the information required under subsection 10.4(1) of the Act.Required wordingThe words “SAFETY”, “RECALL”, “RAPPEL” and “SÉCURITÉ” are required to be clearly visibleon the envelope, or through a window of the envelope, in upper case and in a font size that is larger than the one used for the recipient’s address, if the notice of non-compliance is given to the current owner in paper form; orin the subject line of the communication, in upper case, if the notice of non-compliance is given to the current owner in electronic form.Notice to prescribed person — contentA notice of non-compliance that is given to a prescribed person must contain the following information:the company’s name;for each restraint system or booster seat that may be non-compliant, the model name and number and any other information that is necessary to permit its identification;the number, title or other identification that is assigned by the company to the notice;the motor vehicle safety recall number that is issued by the Department of Transport;a description of the non-compliance, including the causes;operating conditions or other factors that may cause a malfunction of the system or component of the restraint system or booster seat;a description of the safety risk to persons arising from the non-compliance, if any;a description of the corrective measures to be taken in respect of the non-compliance and how they are to be implemented; andany precautions that may be taken to minimize the safety risk until the corrective measures are implemented.Unavailable informationThe company is not required to provide to the prescribed person the information referred to in paragraph (9)(h) if it is not available on the day on which the notice is given but must provide that information as soon as it is available.SOR/2019-253, s. 5
Reports
Initial report — notice to current ownersWithin five working days after the day on which a company begins sending a notice of defect or non-compliance to current owners, the company must provide the Minister with a report containinga copy of the notice;a sample of the envelope used to mail the notice;the date on which the company began sending notices;the date on which the company finished, or expects to finish, sending notices; andthe number of restraint systems or booster seats that are subject to the notice.ExceptionDespite paragraph (1)(b), a company is not required to provide a sample of the envelope if it uses an envelope that has previously been provided as a sample to the Minister and the report includes the date on which the sample was provided.Initial report — notice to prescribed personsWithin five working days after the day on which a company begins sending a notice of defect or non-compliance to prescribed persons, the company must provide to the Minister a report containinga copy of the notice; andif no notices are sent to current owners, the number of restraint systems or booster seats that are subject to the notice.Follow-up reportsFor a period of five years beginning on the 60th day after the day on which a company gives a notice to the Minister under subsection 10(1) or 10.1(1) of the Act, the company must provide the Minister, within five working days after the day on which they are sent to their recipients, a copy of any of the following communications, with the date on which they were sent to their recipients:communications sent to more than one current owner relating to the defect or non-compliance; andcommunications sent to more than one prescribed person relating tothe information set out in subsection 110(9) or 110.01(9), andthe defect or non-compliance.SOR/2019-253, s. 5
Quarterly reportsFor the purposes of section 10.2 of the Act, a company that gives a notice of defect or non-compliance to a current owner or a prescribed person must provide the Minister with quarterly reports that contain the following information:the motor vehicle safety recall number that is issued by the Department of Transport;the number, title or other identification that is assigned by the company to the notice;the number of restraint systems or booster seats that are subject to the notice, including the day on which the number was updated by the company;the number of restraint systems or booster seats for which corrective measures have been taken, including those that required only an inspection, and the day on which that number was determined by the company; anda statement setting out the manner in which the company disposed of the defective parts, restraint systems or booster seats.CalendarThe company must provide the Minister with quarterly reports, in accordance with the following schedule, for a period of two years beginning on the 60th day after the day on which the company gives a notice to the Minister under subsection 10(1) or 10.1(1) of the Act:for the first calendar quarter, from January 1 through March 31, on or before April 30;for the second calendar quarter, from April 1 through June 30, on or before July 30;for the third calendar quarter, from July 1 through September 30, on or before October 30; andfor the fourth calendar quarter, from October 1 through December 31, on or before January 30 of the following year.SOR/2019-253, s. 5
Publication of Information
Information on websiteA company that gives a notice of defect or non-compliance to the Minister under subsection 10(1) or 10.1(1) of the Act must publish the following information, in both official languages, on the website that the company uses to communicate information directed at the Canadian market:the date on which the notice was given to the Minister;the model name and number of the restraint system or booster seat referred to in the notice and any other information that is necessary to permit its identification;the number, title or other identification that is assigned by the company to the notice;the motor vehicle safety recall number that is issued by the Department of Transport;a description ofthe nature of the defect, including the causes of the defect, and its location, orthe non-compliance, including the causes;a description of the safety risk to persons arising from the defect or non-compliance;the type of injury that may result from the defect or non-compliance;a description of the corrective measures to be taken in respect of the defect or non-compliance and how they are to be implemented;any precautions that may be taken to minimize the safety risk until the corrective measures are implemented;a statement that the parts and facilities that are necessary to correct the defect or non-compliance are available or, if they are not, the earliest date by which they are expected to be available;if applicable, a statement indicating that information in respect of notices that are given before a specified date is not available on the website and how to obtain the information;on each web page displaying the information referred to in paragraphs (a) to (k), instructions on how tocontact the company concerning any questions related to the notice,report a safety concern relating to a restraint system or booster seat, andinform the company of a transfer of ownership of a restraint system or booster seat or a change of address; andthe date on which the information was last updated on each web page displaying the information referred to in paragraphs (a) to (k).Date of publicationThe company must publish the information referred to in subsection (1) as soon as feasible, but not later than 60 days after the day on which the company gives the notice to the Minister, and must update the information within seven days after the day on which there is any change to it.ExceptionDespite subsection (2), if the information referred to in paragraph (1)(d), (h) or (j) is not available on the day on which it is to be published, the company must publish the information within seven days after the day on which it becomes available.Minimum period of availability of informationThe company must ensure that the information referred to in subsection (1) remains displayed on the website for at least 10 years beginning on the day on which the company gives the notice of defect or non-compliance to the Minister.HyperlinkThe information referred to in subparagraphs (1)(l)(i) to (iii) may be made available by way of a hyperlink.Availability of informationThe company must ensure that the information referred to in subsection (1) isavailable free of charge;accessible without the user having to register or enter any information; anddisplayed either directly on the website’s home page or made available by way of a hyperlink that contains the word “Recall” or “Recalls” and that is prominently displayed on that home page.ExceptionA company is not required to meet the requirements of this section ifthe requirements have been met by another company that manufactured, sold or imported the restraint system or booster seat; orthe company does not have a website to communicate information directed at the Canadian market.Transitional provisionThis section applies to a company beginning on the first anniversary of the day on which this section comes into force.SOR/2024-274, s. 5
[111 to 199 reserved]CMVSS 213 — Child Restraint SystemsGeneral
InterpretationIn this Part, Test Method 213 means Test Method 213 — Child Restraint Systems (May 2012), published by the Department of Transport.SOR/2013-117, s. 22
Restraint of torso and crotchEvery child restraint system must, when the anthropomorphic test device is positioned in the restraint system in accordance with subsection 4.4.2 or 4.5.2 of Test Method 213,restrain the upper torso by means ofin the case of a forward-facing restraint system,belts passing over each shoulder, ora fixed or movable surface that conforms to the requirements of section 211, orin the case of a rear-facing restraint system, belts passing over each shoulder;restrain the lower torso by means ofa pelvic restraint making an angle of at least 45° but not more than 90° with the seating surface of the restraint system at the pelvic restraint attachment points, ora fixed or movable surface that conforms to the requirements of section 211; andin the case of a forward-facing restraint system, restrain the crotch by means ofa crotch belt that is connectable to the pelvic restraint or to any other device used to restrain the lower torso, ora fixed or movable surface that conforms to the requirements of section 211.
Means of securing forward-facing child restraint systemEvery forward-facing child restraint system must be designed to be secured to a vehicleby means of a vehicle seat belt together with the tether strap provided with the restraint system, without using any other means of attachment; andby means of a lower connector system together with the tether strap provided with the restraint system, without using any other means of attachment.Rear-facing child restraint systemSubject to subsection (3), every rear-facing child restraint system must be designed to be secured to a vehicleby means of a vehicle seat belt, without using any other means of attachment; andby means of a lower connector system, without using any other means of attachment.Rear-facing child restraint system with tether strapIf a rear-facing child restraint system is equipped with a tether strap and the manufacturer recommends its use, the restraint system must be designed to be secured to a vehicleby means of the tether strap together with a vehicle seat belt, without using any other means of attachment; andby means of the tether strap together with a lower connector system, without using any other means of attachment.
Belts and movable surfaces designed to restrain a childEvery belt or movable surface that is part of a child restraint system and that is designed to restrain a child must be adjustable to snugly fit a child whose mass and height are within the ranges indicated in the statement referred to in paragraph 218(1)(d), when the child is positioned in the restraint system in accordance with the instructions referred to in paragraph 220(1)(c) and the restraint system is adjusted in accordance with the instructions referred to in paragraph 220(1)(d).
Audible or visible indicationEvery child restraint system must provide a clear, audible indication when each connector in a lower connector system is securely attached to the lower universal anchorage system or a clear, visual indication that each connector is securely attached to the lower universal anchorage system.
FlammabilityEvery child restraint system must be constructed only of materials that conform to the requirements of TSD 302.SOR/2013-117, s. 23
Belt Buckles and Webbing
Conformity with TSD 209Every belt buckle and related piece of adjustment hardware and every tether strap attachment and related piece of adjustment hardware that are part of a child restraint system must conform to the requirements of S4.3(a)(2) and (b) of TSD 209.
Belt bucklesEvery belt buckle that is fitted on a belt designed to restrain a child in a child restraint system mustunder the conditions set out in section 3 of Test Method 213,not release when any force of less than 40 N is applied, andrelease when a force of at least 40 N but not more than 62 N is applied;under the conditions set out in section 5 of Test Method 213, release when a force of not more than 71 N is applied;conform to the requirements of S4.3(d)(2) of TSD 209, except that the surface area of a belt buckle designed for push-button application must be at least 385 mm2;conform to the requirements of S4.3(g) of TSD 209; andnot release during the dynamic tests specified in section 4 of Test Method 213.SOR/2013-117, s. 24
WebbingAny webbing that is designed to secure a child restraint system to a user-ready tether anchorage or to a lower universal anchorage system, or to restrain a child within the restraint system, mustwhen tested in accordance with S5.1(b) of TSD 209, before being tested for resistance to abrasion as specified in S5.1(d) or S5.3(c) of TSD 209, for resistance to light as specified in S5.1(e) of TSD 209 or for resistance to micro-organisms as specified in S5.1(f) of TSD 209, have a breaking strength ofat least 15 000 N, in the case of webbing designed to secure the restraint system to the user-ready tether anchorage or to the lower universal anchorage system, orat least 11 000 N, in the case of webbing designed to restrain a child within the restraint system;when tested in accordance with S5.1(b) of TSD 209, after being tested for resistance to abrasion as specified in S5.1(d) or S5.3(c) of TSD 209, have a breaking strength of at least 75% of its initial breaking strength;conform to the requirements respecting breaking strength set out in S4.2(e) and (f) of TSD 209; andif contactable by the torso when the restraint system is tested in accordance with section 4 of Test Method 213, have a width of not less than 38 mm, measured as specified in S5.1(a) of TSD 209.SOR/2013-117, s. 16
Contactable Surfaces
Contactable surfacesEvery child restraint system must providefor the support of the child’s back, a continuous surface that is flat or concave and has an area of not less than 54 800 mm2; andfor the support of the sides of the child’s torso, continuous surfaces that are flat or concave and have an area of not less than 30 500 mm2 each.
ProhibitionA child restraint system must not have any surface directly in front of the child, unless the surface is designed to limit the forward movement of the child.
Cross-sections of surfaceEvery horizontal cross-section of a surface of a child restraint system that is designed to limit the forward movement of a child must be flat or concave, and every vertical longitudinal cross-section of that surface must be flat or convex with a radius of curvature of the underlying structure of not less than 50 mm.
Rigid structural elementsAny rigid structural element underlying a contactable surface of a child restraint system must not havea protrusion, with any padding or flexible overlay material removed, of more than 9.5 mm; oran exposed edge with a radius of less than 6.4 mm.
Surface contactable by headEvery surface of a child restraint system that is contactable by the head of an anthropomorphic test device positioned in the restraint system in accordance with subsection 4.4.2 or 4.5.2 of Test Method 213 must be covered with slow-recovery, energy-absorbing material that, when tested in accordance with section 6 of Test Method 213, hasa resistance of not less than 4 kPa but not more than 70 kPa at 25% of compression-deflection resistance;a thickness of not less than 12 mm, if the material has a resistance of not less than 12 kPa but not more than 70 kPa at 25% of compression-deflection resistance; anda thickness of not less than 19 mm, if the material has a resistance of not less than 4 kPa but less than 12 kPa at 25% of compression-deflection resistance.
Testing
Inversion testingA child restraint system that is subjected to an inversion test in accordance with section 7 of Test Method 213 must not fall out of the aircraft passenger seat belt, and the anthropomorphic test device must not fall out of the restraint system, at any time during the rotation or three-second immobilisation period referred to in that section.
Dynamic testingA child restraint system that is subjected to a dynamic test in accordance with section 4 of Test Method 213 must, when in any adjustment position for which there is no warning under subparagraph 218(1)(e)(iii),exhibit no complete separation of any load-bearing structural element, and no partial separation exposing a surface witha protrusion of more than 9.5 mm, ora radius of less than 6.4 mm;remain in the same adjustment position during the test as it was in immediately before the test began;except in the case of a restraint system tested with the anthropomorphic test device specified in subpart S, part 572, chapter V, title 49 of the Code of Federal Regulations of the United States (revised as of October 1, 2012), limit the resultant acceleration at the location of the accelerometer mounted in the upper thorax of the anthropomorphic test device to not more than 60 g, except for intervals of not more than 3 ms;except in the case of a restraint system tested with the anthropomorphic test device specified in subpart S, part 572, chapter V, title 49 of the Code of Federal Regulations of the United States (revised as of October 1, 2012), limit the resultant acceleration of the centre of gravity of the head of the anthropomorphic test device during the movement of the head towards the front of the vehicle to not more than 80 g, except for intervals of not more than 3 ms, unless it is established that any resultant acceleration above 80 g is caused by another part of the anthropomorphic test device striking its head;subject to subsection 216(2), limit the movement of the head of the anthropomorphic test device towards the rear of the restraint system by means of a continuous seat back that is an integral part of the restraint system; andsubject to subsection 216(2), limit the rotation of the head of the anthropomorphic test device towards the rear of the restraint system, in its midsagittal plane, by means of a continuous seat back that is an integral part of the restraint system, so that the angle between the head and the torso is at no time during the test more than 45° as compared to the angle between the head and the torso prior to the test.Continuous seat backThe continuous seat back referred to in paragraphs (1)(e) and (f) must havea heightof at least 500 mm, in the case of a child restraint system recommended by the manufacturer for use by a child whose mass is 18 kg or less, orof at least 560 mm, in the case of a child restraint system recommended by the manufacturer for use by a child whose mass is more than 18 kg; anda width of at least 200 mm, measured in the horizontal plane at the height specified in paragraph (a).Measurement of height — paragraph (2)(a)The height referred to in paragraph (2)(a) must be measured in a plane parallel to the surface of the seat back of the child restraint system and orthogonal to the vertical longitudinal plane passing through the longitudinal centreline of the restraint system, from the lowest point of the restraint system’s seating surface that is contacted by the buttocks of the seated anthropomorphic test device.ExceptionDespite paragraph (2)(b), if the child restraint system provides surfaces for the support of the sides of the torso, and those surfaces extend at least 100 mm forward from the padded surface of the portion of the restraint system provided for the support of the head of the anthropomorphic test device, the restraint system may have a continuous seat back width of not less than 150 mm, measured in the horizontal plane at the height referred to in paragraph (2)(a).BeltEvery belt that is part of a child restraint system and that is designed to restrain a child in the restraint system must not, when subjected to a dynamic test in accordance with section 4 of Test Method 213, impose on the anthropomorphic test device any loads that result from the mass of the restraint system or the mass of the seat back of the standard seat assembly.SOR/2013-117, s. 25
Forward-facing child restraint systemA forward-facing child restraint system that is subjected to a dynamic test in accordance with section 4 of Test Method 213 must not, when in any adjustment position for which there is no warning under subparagraph 218(1)(e)(iii),except in the case of a restraint system tested with the anthropomorphic test device specified in subpart S, part 572, chapter V, title 49 of the Code of Federal Regulations of the United States (revised as of October 1, 2012), allow any portion of the head of the anthropomorphic test device to pass through the vertical transverse plane — shown as the forward excursion limit in Figures 5 and 6 of Schedule 7 — that is 720 mm forward of the Z point on the standard seat assembly, measured along the SORL;except in the case of a restraint system tested with the anthropomorphic test device specified in subpart S, part 572, chapter V, title 49 of the Code of Federal Regulations of the United States (revised as of October 1, 2012), allow either knee pivot point to pass through the vertical transverse plane — shown as the forward excursion limit in Figures 5 and 6 of Schedule 7 — that is 915 mm forward of the Z point on the standard seat assembly, measured along the SORL; andallow the angle between the restraint system’s back support surface and seating surface to be less than 45° at the completion of the test.ExceptionA forward-facing child restraint system is not required to conform to the requirements of paragraphs 215(1)(e) and (f) if the target point located on either side of the head of the heaviest of the anthropomorphic test devices used in the dynamic test — other than an anthropomorphic test device specified in subpart I, N or S, part 572, chapter V, title 49 of the Code of Federal Regulations of the United States (revised as of October 1, 2012) — and located on the transverse axis passing through the centre of mass of the device’s head and perpendicular to the head’s midsagittal plane is below a horizontal plane tangent to the top of the standard seat assembly when the anthropomorphic test device is positioned in the restraint system in accordance with subsection 4.4.2 or 4.5.2 of Test Method 213 and the restraint system is installed on the standard seat assembly in accordance with subsection 4.4.1 or 4.5.1 of Test Method 213.SOR/2013-117, s. 25
Rear-facing child restraint systemA rear-facing child restraint system that is subjected to a dynamic test in accordance with section 4 of Test Method 213 must, when in any adjustment position for which there is no warning under subparagraph 218(1)(e)(iii),retain the torso of the anthropomorphic test device within the restraint system, and not allow any portion of the target points on either side of the device’s head, located on the transverse axis passing through the centre of mass of the device’s head and perpendicular to the head’s midsagittal plane, to pass at any time, during or immediately after the test, either through the transverse orthogonal planes formed by the extension of the seat back frontal surface plane of the restraint system and by the plane that passes through the uppermost point of the restraint system, as shown in Figure 7 of Schedule 7, or through the vertical transverse plane passing through point X on the standard seat assembly, as shown in Figure 8 of Schedule 7; andnot allow the angle between the vertical and the back and head support surface, measured 240 mm above the seating surface, to be more than 70° at any time during the test.
Information
InformationEvery child restraint system must have stitched onto it, indelibly moulded into or onto it, or indelibly printed on a label affixed to it in a permanent manner, the following information:the name of the company that manufactured, imported or sold the restraint system and the address of its principal place of business;the model name and number of the restraint system;the date of manufacture of the restraint system, as shown in Schedule 5, with the year, month and day above the corresponding wording in both official languages;a statement indicating — in units based on the International System of Units followed by the corresponding imperial units in parentheses — the mass and height range of the children for whom the manufacturer recommends the restraint system when it is used in a forward-facing and, where applicable, a rear-facing position;a warning indicatingif the restraint system can be used in a forward-facing position, that it must be secured to the vehicle as shown in the installation instructions by means of the tether strap provided with the restraint system and by either of the following means:a lower connector system, if the restraint system is installed in a seating position that is equipped with a lower universal anchorage system, ora vehicle seat belt, if the restraint system is installed in a seating position that is not equipped with a lower universal anchorage system,if the restraint system can be used in a rear-facing position, that it must be secured to the vehicle as shown in the installation instructions by either of the following means and, if the restraint system is equipped with a tether strap and the manufacturer recommends its use, by means of the tether strap:a lower connector system, if the restraint system is installed in a seating position that is equipped with a lower universal anchorage system, ora vehicle seat belt, if the restraint system is installed in a seating position that is not equipped with a lower universal anchorage system,if the restraint system is not designed to be used at certain adjustment positions, that those adjustment positions must not be used,if the restraint system is equipped with belts for restraining a child, that the belts must be snugly adjusted around the child, andif the restraint system is equipped with a fixed or movable surface for restraining the child and also requires the use of belts to restrain the child, that the surface alone is not sufficient to restrain the child;if the restraint system can be used in a forward-facing position, an installation diagram that shows the restraint systeminstalled in a forward-facing position as recommended by the manufacturer in a seating position that is equipped only with a lap belt, and secured to the vehicle by means of the belt and by means of the tether strap,installed in a forward-facing position as recommended by the manufacturer in a seating position that is equipped only with a continuous-loop lap and shoulder belt, and secured to the vehicle by means of the belt and by means of the tether strap, andinstalled in a forward-facing position as recommended by the manufacturer in a seating position that is equipped with a lower universal anchorage system, and secured to the vehicle by means of a lower connector system and by means of the tether strap; andif the restraint system can be used in a rear-facing position, an installation diagram that shows the restraint systeminstalled in a rear-facing position as recommended by the manufacturer in a seating position that is equipped only with a lap belt, and secured to the vehicle by means of the belt and, if the restraint system is equipped with a tether strap and the manufacturer recommends its use, by means of the tether strap,installed in a rear-facing position as recommended by the manufacturer in a seating position that is equipped only with a continuous-loop lap and shoulder belt, and secured to the vehicle by means of the belt and, if the restraint system is equipped with a tether strap and the manufacturer recommends its use, by means of the tether strap, andinstalled in a rear-facing position as recommended by the manufacturer in a seating position that is equipped with a lower universal anchorage system, and secured to the vehicle by means of a lower connector system and, if the restraint system is equipped with a tether strap and the manufacturer recommends its use, by means of the tether strap.Official languages and print sizeThe information referred to in subsection (1) must be in both official languages and in characters of at least 10 points, except for the words “year/année”, “month/mois” and “day/jour” under the date of manufacture, which may be in characters of at least 8 points.Visibility of informationThe information referred to in paragraphs (1)(d) to (g) must be fully visible at all times, even when the restraint system is occupied.
Warning — air bagEvery child restraint system that can be used in a rear-facing position must bear the air bag warning label shown in Schedule 6, and the label must conform to the requirements of that schedule.IdemThe label referred to in subsection (1) must be affixed in a permanent manner at either of the following locations and be fully visible to a person installing the restraint system:on the side of the restraint system that will face the right front passenger door when the restraint system is facing rearward; orat the location where the child’s head would rest or adjacent to that location.
Installation instructionsEvery child restraint system must be accompanied by printed instructions, in both official languages, that set out a step-by-step procedure, including diagrams, forinstalling and securing the restraint system in a vehicle;installing the restraint system in an aircraft passenger seat referred to in subsection 2.1.2 of Test Method 213;positioning a child in the restraint system; andadjusting every part of the restraint system that is designed to restrain the child.IdemThe instructions referred to in paragraph (1)(a) must state that the restraint system, even when unoccupied, must be firmly secured to the vehicle.IdemThe instructions mustspecify the classes of vehicles, the seating positions and the types of vehicle seat belts with which the restraint system may or may not be used;specify that the restraint system may be used with a lower universal anchorage system; andexplain the primary consequences of not following the warnings appearing on the restraint system.Storage of instructionsEvery child restraint system must have a place for the storage of instructions.
[221 to 299 reserved]CMVSS 213.1 — Infant Restraint SystemsGeneral
InterpretationIn this Part, Test Method 213.1 means Test Method 213.1 — Infant Restraint Systems (May 2012), published by the Department of Transport.SOR/2013-117, s. 22
Restraint system designed to face the rearEvery infant restraint system must be designed to face the rear of the vehicle.
Restraint of torsoEvery infant restraint system must, when the anthropomorphic test device is positioned in the restraint system in accordance with subsection 4.5.2 or 4.6.2 of Test Method 213.1,restrain the upper torso by means of belts passing over each shoulder; andrestrain the lower torso.
Means of securing restraint systemSubject to subsection (2), every infant restraint system must be designed to be secured to a vehicleby means of a vehicle seat belt in such a manner that the belt will not impose directly on the infant any loads that result from the mass of the restraint system, and without using any other means of attachment; andby means of a lower connector system, without using any other means of attachment.Restraint system with tether strapIf an infant restraint system is equipped with a tether strap and the manufacturer recommends its use, the restraint system must be designed to be secured to a vehicleby means of the tether strap together with a vehicle seat belt in such a manner that the belt will not impose directly on the infant any loads that result from the mass of the restraint system, and without using any other means of attachment; andby means of the tether strap together with a lower connector system, without using any other means of attachment.
Restraint system with removable baseIf an infant restraint system is manufactured with a removable base and the seating component of the restraint system is designed to be used in a vehicle with or without the base, the restraint system must be equipped with a lower connector system on the base.
Part designed to restrain an infantEvery part of an infant restraint system that is designed to restrain an infant must be adjustable to snugly fit an infant whose mass and height are within the ranges indicated in the statement referred to in paragraph 316(1)(d), when the infant is positioned in the restraint system in accordance with the instructions referred to in paragraph 318(1)(c) and the restraint system is adjusted in accordance with the instructions referred to in paragraph 318(1)(d).
Audible or visible indicationEvery infant restraint system must provide a clear, audible indication when each connector in a lower connector system is securely attached to the lower universal anchorage system or a clear, visual indication that each connector is securely attached to the lower universal anchorage system.
FlammabilityEvery infant restraint system must be constructed only of materials that conform to the requirements of TSD 302.SOR/2013-117, s. 23
Belt Buckles and Webbing
Conformity with TSD 209Every belt buckle and related piece of adjustment hardware and every tether strap attachment and related piece of adjustment hardware that are part of an infant restraint system must conform to the requirements of S4.3(a)(2) and (b) of TSD 209.
Belt bucklesEvery belt buckle that is fitted on a belt designed to restrain an infant in an infant restraint system mustunder the conditions set out in section 3 of Test Method 213.1,not release when any force of less than 40 N is applied, andrelease when a force of at least 40 N but not more than 62 N is applied;under the conditions set out in section 5 of Test Method 213.1, release when a force of not more than 71 N is applied;conform to the requirements of S4.3(d)(2) of TSD 209, except that the surface area of a belt buckle designed for push-button application must be at least 385 mm2;conform to the requirements of S4.3(g) of TSD 209; andnot release during the dynamic tests specified in section 4 of Test Method 213.1.SOR/2013-117, s. 24
WebbingAny webbing that is designed to secure an infant restraint system to a user-ready tether anchorage or to a lower universal anchorage system, or to restrain an infant within the restraint system, mustwhen tested in accordance with S5.1(b) of TSD 209, before being tested for resistance to abrasion as specified in S5.1(d) or S5.3(c) of TSD 209, for resistance to light as specified in S5.1(e) of TSD 209 or for resistance to micro-organisms as specified in S5.1(f) of TSD 209, have a breaking strength ofat least 15 000 N in the case of webbing designed to secure the restraint system to the user-ready tether anchorage or to the lower universal anchorage system, orat least 11 000 N in the case of webbing designed to restrain an infant within the restraint system;when tested in accordance with S5.1(b) of TSD 209, after being tested for resistance to abrasion as specified in S5.1(d) or S5.3(c) of TSD 209, have a breaking strength of at least 75% of its initial breaking strength;conform to the requirements respecting breaking strength set out in S4.2(e) and (f) of TSD 209; andif contactable by the torso when the restraint system is tested in accordance with section 4 of Test Method 213.1, have a width of not less than 38 mm, measured as specified in S5.1(a) of TSD 209.SOR/2013-117, s. 17
Contactable Surfaces
Contactable surfacesEvery infant restraint system must providefor the support of the infant’s back, a continuous surface that is flat or concave and has an area of not less than 54 800 mm2; andfor the support of the sides of the infant’s torso, continuous surfaces that are flat or concave and have an area of not less than 30 500 mm2 each.
Rigid structural elementsAny rigid structural element underlying a contactable surface of an infant restraint system must not havea protrusion, with any padding or flexible overlay material removed, of more than 9.5 mm; oran exposed edge with a radius of less than 6.4 mm.
Surface contactable by headEvery surface of an infant restraint system that is contactable by the head of an anthropomorphic test device positioned in the restraint system in accordance with subsection 4.5.2 or 4.6.2 of Test Method 213.1 must be covered with slow-recovery, energy-absorbing material that, when tested in accordance with section 6 of Test Method 213.1, hasa resistance of not less than 4 kPa but not more than 70 kPa at 25% of compression-deflection resistance;a thickness of not less than 12 mm, if the material has a resistance of not less than 12 kPa but not more than 70 kPa at 25% of compression-deflection resistance; anda thickness of not less than 19 mm, if the material has a resistance of not less than 4 kPa but less than 12 kPa at 25% of compression-deflection resistance.
Testing
Inversion testingAn infant restraint system that is subjected to an inversion test in accordance with section 7 of Test Method 213.1 must not fall out of the aircraft passenger seat belt, and the anthropomorphic test device must not fall out of the restraint system, at any time during the rotation or three-second immobilization period referred to in that section.
Dynamic testingAn infant restraint system that is subjected to a dynamic test in accordance with section 4 of Test Method 213.1 must, if the adjustment position of each component of the restraint system is in accordance with the manufacturer’s instructions,exhibit no complete separation of any load-bearing structural element, and no partial separation exposing a surface witha protrusion of more than 9.5 mm, ora radius of less than 6.4 mm;remain in the same adjustment position during the test as it was in immediately before the test began, except that, if the restraint system has a means of automatically repositioning the seating surface to allow the anthropomorphic test device to move from a reclined position to a more upright position and back to a reclined position during the test, the seating surface does not have to remain in the same adjustment position during the test as it was in immediately before the test began;limit the resultant acceleration at the location of the accelerometer mounted in the upper thorax of the anthropomorphic test device to not more than 60 g, except for intervals of not more than 3 ms;limit the resultant acceleration of the centre of gravity of the head of the anthropomorphic test device during the movement of the head towards the front of the vehicle to not more than 80 g, except for intervals of not more than 3 ms, unless it is established that any resultant acceleration above 80 g is caused by another part of the anthropomorphic test device striking its head;retain the torso of the anthropomorphic test device within the restraint system, and not allow any portion of the target points on either side of the device’s head, located on the transverse axis passing through the centre of mass of the device’s head and perpendicular to the head’s midsagittal plane, to pass at any time, during or immediately after the test, either through the transverse orthogonal planes formed by the extension of the seat back frontal surface plane of the restraint system and by the plane that passes through the uppermost point of the restraint system, as shown in Figure 7 of Schedule 7, or through the vertical transverse plane passing through point X on the standard seat assembly, as shown in Figure 8 of Schedule 7;not allow the angle between the vertical and the back and head support surface, measured 240 mm above the seating surface, to be more than 70° at any time during the test;limit the movement of the head of the anthropomorphic test device towards the rear of the restraint system by means of a continuous seat back that is an integral part of the restraint system; andlimit the rotation of the head of the anthropomorphic test device towards the rear of the restraint system, in its midsagittal plane, by means of a continuous seat back that is an integral part of the restraint system, so that the angle between the head and the torso is at no time during the test more than 45° as compared to the angle between the head and the torso prior to the test.Dynamic testing — levelling deviceAn infant restraint system that is subjected to a dynamic test in accordance with section 4 of Test Method 213.1 must conform to the requirements of paragraphs (1)(a) and (b) if the restraint system is equipped with a levelling device and the adjustment position of each component of the restraint system, except the levelling device, is in accordance with the manufacturer’s instructions.Continuous seat backThe continuous seat back referred to in paragraphs (1)(g) and (h) musthave a height of at least 500 mm;have a width of at least 200 mm, measured in the horizontal plane at the height specified in paragraph (a); andnot impose any loads on the top of the head of the anthropomorphic test device during the dynamic test referred to in subsection (1).Measurement of height — paragraph (3)(a)The height referred to in paragraph (3)(a) must be measured in a plane parallel to the surface of the seat back of the infant restraint system and orthogonal to the vertical longitudinal plane passing through the longitudinal centreline of the restraint system, from the lowest point of the restraint system’s seating surface that is contacted by the buttocks of the seated anthropomorphic test device.ExceptionDespite paragraph (3)(b), if the infant restraint system provides surfaces for the support of the sides of the torso, and those surfaces extend at least 100 mm forward from the padded surface of the portion of the restraint system provided for the support of the head of the anthropomorphic test device, the restraint system may have a continuous seat back width of not less than 150 mm, measured in the horizontal plane at the height specified in paragraph (3)(a).Restraint system with means of automatic repositioningIf an infant restraint system that has a means of automatically repositioning the seating surface is subjected, in any adjustment position, to a dynamic test in accordance with section 4 of Test Method 213.1, an opening that is exposed and larger than 6.4 mm before the test must not become smaller during the test as a result of the movement of the seating surface relative to the other parts of the restraint system.
Information
InformationEvery infant restraint system must have stitched onto it, indelibly moulded into or onto it, or indelibly printed on a label affixed to it in a permanent manner, the following information:the name and principal place of business of the company that manufactured, imported or sold the restraint system;the model name and number of the restraint system;the date of manufacture of the restraint system, as shown in Schedule 5, with the year, month and day above the corresponding wording in both official languages;a statement indicating — in units based on the International System of Units followed by the corresponding imperial units in parentheses — the mass and height range of the infants for whom the manufacturer recommends the restraint system;a warning indicatingthat the restraint system must be used only in a forward-facing seating position equipped with a vehicle seat belt or a lower universal anchorage system,that the restraint system must be in a rear-facing position when it is used for an infant,that the restraint system must be secured to the vehicle as shown in the installation instructions by either of the following means and, if the restraint system is equipped with a tether strap and the manufacturer recommends its use, by means of the tether strap:a lower connector system, if the restraint system is installed in a seating position that is equipped with a lower universal anchorage system, ora vehicle seat belt, if the restraint system is installed in a seating position that is not equipped with a lower universal anchorage system, andif the restraint system is equipped with belts for restraining an infant, that the belts must be snugly adjusted around the infant; andan installation diagram that shows the restraint systeminstalled as recommended by the manufacturer in a seating position that is equipped only with a lap belt, and secured to the vehicle by means of the belt and, if the restraint system is equipped with a tether strap and the manufacturer recommends its use, by means of the tether strap,installed as recommended by the manufacturer in a seating position that is equipped only with a continuous-loop lap and shoulder belt, and secured to the vehicle by means of the belt and, if the restraint system is equipped with a tether strap and the manufacturer recommends its use, by means of the tether strap, andinstalled as recommended by the manufacturer in a seating position that is equipped with a lower universal anchorage system, and secured to the vehicle by means of a lower connector system and, if the restraint system is equipped with a tether strap and the manufacturer recommends its use, by means of the tether strap.Official languages and print sizeThe information referred to in subsection (1) must be in both official languages and in characters of at least 10 points, except for the words “year/année”, “month/mois” and “day/jour” under the date of manufacture, which may be in characters of at least 8 points.Visibility of informationThe information referred to in paragraphs (1)(d) to (f) must be fully visible at all times, even when the restraint system is occupied, whether the restraint system is installed with or without a removable base.
Warning — air bagEvery infant restraint system must bear the air bag warning label shown in Schedule 6, and the label must conform to the requirements of that schedule.IdemThe label referred to in subsection (1) must be affixed in a permanent manner at either of the following locations and be fully visible to a person installing the restraint system:on the side of the restraint system that will face the right front passenger door when the restraint system is facing rearward; orat the location where the infant’s head would rest or adjacent to that location.
Installation instructionsEvery infant restraint system must be accompanied by printed instructions, in both official languages, that set out a step-by-step procedure, including diagrams, forinstalling and securing the restraint system in a vehicle;installing the restraint system in an aircraft passenger seat referred to in subsection 2.1.2 of Test Method 213.1;positioning an infant in the restraint system; andadjusting every part of the restraint system that is designed to restrain the infant.IdemThe instructions referred to in paragraph (1)(a) must state that the restraint system, even when unoccupied, must be firmly secured to the vehicle.IdemThe instructions mustspecify the classes of vehicles, the seating positions and the types of vehicle seat belts with which the restraint system may or may not be used;specify that the restraint system may be used with a lower universal anchorage system;if the restraint system has a means of automatically repositioning the seating surface, specify that the ability of the restraint system to change position must not be impeded;explain the primary consequences of not following the warnings appearing on the restraint system; andif the restraint system is manufactured with a removable base and the seating component of the restraint system is designed to be used in a vehicle with or without the base, specify whether the restraint system must be used with or without the base when the restraint system is installed in an aircraft passenger seat.Storage of instructionsEvery infant restraint system must have a place for the storage of instructions.
[319 to 399 reserved]CMVSS 213.2 — Booster SeatsGeneral
InterpretationIn this Part, Test Method 213.2 means Test Method 213.2 — Booster Seats (May 2012), published by the Department of Transport.SOR/2013-117, s. 22
Means of securing booster seatSubject to subsection (2), every booster seat must be designed to be secured to a vehicleby means of a vehicle seat belt, without using any other means of attachment; andif the booster seat is equipped with a lower connector system and the manufacturer recommends its use, by means of the lower connector system, without using any other means of attachment.Booster seat with tether strapIf the booster seat is equipped with a tether strap and the manufacturer recommends its use, the booster seat must be designed to be secured to a vehicleby means of the tether strap together with a vehicle seat belt, without using any other means of attachment; andif the booster seat is equipped with a lower connector system and the manufacturer recommends its use, by means of the tether strap together with the lower connector system, without using any other means of attachment.Forward movement of torsoA booster seat must not have any part that limits the forward movement of the torso during frontal impact.
Audible or visible indicationEvery booster seat that is equipped with a lower connector system must provide a clear, audible indication when each connector in a lower connector system is securely attached to the lower universal anchorage system or a clear, visual indication that each connector is securely attached to the lower universal anchorage system.
FlammabilityEvery booster seat must be constructed only of materials that conform to the requirements of TSD 302.SOR/2013-117, s. 23
Tether Strap Attachments and Webbing
Conformity with TSD 209Every tether strap attachment and related piece of adjustment hardware that is part of a booster seat must conform to the requirements of S4.3(a)(2) and (b) of TSD 209.
WebbingAny webbing that is designed to secure a booster seat to a user-ready tether anchorage or to a lower universal anchorage system mustwhen tested in accordance with S5.1(b) of TSD 209, before being tested for resistance to abrasion as specified in S5.1(d) or S5.3(c) of TSD 209, for resistance to light as specified in S5.1(e) of TSD 209 or for resistance to micro-organisms as specified in S5.1(f) of TSD 209, have a breaking strength of at least 15 000 N;when tested in accordance with S5.1(b) of TSD 209, after being tested for resistance to abrasion as specified in S5.1(d) or S5.3(c) of TSD 209, have a breaking strength of at least 75% of its initial breaking strength; andconform to the requirements respecting breaking strength set out in S4.2(e) and (f) of TSD 209.SOR/2013-117, s. 18
Contactable Surfaces
Rigid structural elementsAny rigid structural element underlying a contactable surface of a booster seat must not havea protrusion, with any padding or flexible overlay material removed, of more than 9.5 mm; oran exposed edge with a radius of less than 6.4 mm.
Testing
Dynamic testingA booster seat that is subjected to a dynamic test in accordance with section 3 of Test Method 213.2 must, when in any adjustment position,exhibit no complete separation of any load-bearing structural element, and no partial separation exposing a surface witha protrusion of more than 9.5 mm, ora radius of less than 6.4 mm;remain in the same adjustment position during the test as it was in immediately before the test began, except a component of the booster seat used to ensure that the vehicle seat belt is adjusted as recommended by the manufacturer;except in the case of a booster seat tested with the anthropomorphic test device specified in subpart S, part 572, chapter V, title 49 of the Code of Federal Regulations of the United States (revised as of October 1, 2012), limit the resultant acceleration at the location of the accelerometer mounted in the upper thorax of the anthropomorphic test device to not more than 60 g, except for intervals of not more than 3 ms;except in the case of a booster seat tested with the anthropomorphic test device specified in subpart S, part 572, chapter V, title 49 of the Code of Federal Regulations of the United States (revised as of October 1, 2012), limit the resultant acceleration of the centre of gravity of the head of the anthropomorphic test device during the movement of the head towards the front of the vehicle to not more than 80 g, except for intervals of not more than 3 ms, unless it is established that any resultant acceleration above 80 g is caused by another part of the anthropomorphic test device striking its head;except in the case of a booster seat tested with the anthropomorphic test device specified in subpart S, part 572, chapter V, title 49 of the Code of Federal Regulations of the United States (revised as of October 1, 2012), not allow any portion of the head of the anthropomorphic test device to pass through the vertical transverse plane — shown as the forward excursion limit in Figures 5 and 6 of Schedule 7 — that is 813 mm forward of the Z point on the standard seat assembly, measured along the SORL; andexcept in the case of a booster seat tested with the anthropomorphic test device specified in subpart S, part 572, chapter V, title 49 of the Code of Federal Regulations of the United States (revised as of October 1, 2012), not allow either knee pivot point to pass through the vertical transverse plane — shown as the forward excursion limit in Figures 5 and 6 of Schedule 7 — that is 915 mm forward of the Z point on the standard seat assembly, measured along the SORL.SOR/2013-117, s. 25
Quasi-static testA booster seat that is subjected to a quasi-static test in accordance with section 4 of Test Method 213.2 must not deflect more than 25 mm.SOR/2013-117, s. 19
Information
InformationEvery booster seat must have stitched onto it, indelibly moulded into or onto it, or indelibly printed on a label affixed to it in a permanent manner, the following information:the name and principal place of business of the company that manufactured, imported or sold the booster seat;the model name and number of the booster seat;the date of manufacture of the booster seat, as shown in Schedule 5, with the year, month and day above the corresponding wording in both official languages;a statement indicating that the booster seat must be used only by persons whose mass is at least 18 kg;a statement indicating — in units based on the International System of Units followed by the corresponding imperial units in parentheses — the mass and height range of the persons for whom the manufacturer recommends the booster seat; andan installation diagram that shows the booster seat occupant restrained to the vehicle by means of a continuous-loop lap and shoulder belt and the booster seat installed as recommended by the manufacturer, andif the booster seat is equipped with a tether strap and the manufacturer recommends its use, the booster seat secured to the vehicle by means of the tether strap, andif the booster seat is equipped with a lower connector system and the manufacturer recommends its use, the booster seat secured to the vehicle by means of the lower connector system.Official languages and print sizeThe information referred to in subsection (1) must be in both official languages and in characters of at least 10 points, except for the words “year/année”, “month/mois” and “day/jour” under the date of manufacture, which may be in characters of at least 8 points.Visibility of informationThe information referred to in paragraphs (1)(d) to (f) must be fully visible at all times, even when the booster seat is occupied.
Installation instructionsEvery booster seat must be accompanied by printed instructions, in both official languages, that set out a step-by-step procedure, including diagrams, forinstalling and securing the booster seat in a vehicle;positioning a person in the booster seat; andadjusting every part of the booster seat.IdemThe instructions referred to in paragraph (1)(a) must state that the booster seat, even when unoccupied, must be firmly secured to the vehicle.IdemThe instructions mustspecify the classes of vehicles, the seating positions and the types of vehicle seat belts with which the booster seat may or may not be used;specify whether the booster seat may be used with a lower universal anchorage system; andexplain the primary consequences of not following the warnings appearing on the booster seat.Storage of instructionsEvery booster seat must have a place for the storage of instructions.
[411 to 499 reserved]CMVSS 213.3 — Restraint Systems for Disabled PersonsGeneral
InterpretationIn this Part, Test Method 213.3 means Test Method 213.3 — Restraint Systems for Disabled Persons (May 2012), published by the Department of Transport.SOR/2013-117, s. 22
Restraint of torso and crotchEvery restraint system for disabled persons mustrestrain the upper torso by means ofin the case of a forward-facing restraint system,belts passing over each shoulder, ora fixed or movable surface that conforms to the requirements of section 514, orin the case of a rear-facing restraint system, belts passing over each shoulder;restrain the lower torso by means ofa pelvic restraint making an angle of at least 45° but not more than 90° with the seating surface of the restraint system at the pelvic restraint attachment points, ora fixed or movable surface that conforms to the requirements of section 514; andin the case of a forward-facing restraint system, restrain the crotch by means ofa crotch belt that is connectable to the pelvic restraint or to any other device used to restrain the lower torso, ora fixed or movable surface that conforms to the requirements of section 514.
Means of securing restraint systemSubject to subsection (2), every mass-produced restraint system for disabled persons must be designed to be secured to a vehicleby means of a vehicle seat belt, without using any other means of attachment; andif the restraint system is equipped with a lower connector system and the manufacturer recommends its use, by means of the lower connector system, without using any other means of attachment.Restraint system with tether strapIf the mass-produced restraint system for disabled persons is equipped with a tether strap and the manufacturer recommends its use, the restraint system must be designed to be secured to a vehicleby means of the tether strap together with a vehicle seat belt, without using any other means of attachment; andif the restraint system is equipped with a lower connector system and the manufacturer recommends its use, by means of the tether strap together with the lower connector system, without using any other means of attachment.
Audible or visible indicationEvery mass-produced restraint system for disabled persons that is equipped with a lower connector system must provide a clear, audible indication when each connector in a lower connector system is securely attached to the lower universal anchorage system or a clear, visual indication that each connector is securely attached to the lower universal anchorage system.
Custom restraint systemEvery custom restraint system for a disabled person, other than a custom restraint system for a disabled person that is designed to be used only in school buses, must be designed to be secured to a vehicle by means of a vehicle seat belt together with the tether strap provided with the restraint system, without using any other means of attachment.Custom restraint system — school busesEvery custom restraint system for a disabled person that is designed to be used only in school buses must be designed to be secured to a school bus by either or both of the following means:a vehicle seat belt together with the tether strap provided with the restraint system, without using any other means of attachment; andbelts that wrap around a school bus seat or seat back, without using any other means of attachment.
FlammabilityEvery restraint system for disabled persons must be constructed only of materials that conform to the requirements of TSD 302.SOR/2013-117, s. 23
Belts, Buckles and Webbing
BeltsEvery belt that is part of a restraint system for disabled persons and that is designed to restrain a disabled person must not impose on the person any loads that result from the mass of the restraint system.
Release mechanism of a beltEvery release mechanism of a belt used in a restraint system for disabled persons mustbe easy to locate and to operate and be readily accessible to a person assisting the disabled person;be designed to minimize the possibility of accidental release; andnot be of the hook and loop fastener type (for example, a Velcro-type fastener).
Conformity with TSD 209Every belt buckle and related piece of adjustment hardware and every tether strap attachment and related piece of adjustment hardware that are part of a restraint system for disabled persons must conform to the requirements of S4.3(a)(2) and (b) of TSD 209.
Belts or movable surfaces designed to restrain a person — mass-produced restraint systemsEvery belt or movable surface that is part of a mass-produced restraint system for disabled persons and that is designed to restrain a disabled person must be adjustable to snugly fit a person whose mass and height are within the ranges indicated in the statement referred to in paragraph 521(1)(d), when the person is positioned in the restraint system in accordance with the instructions referred to in paragraph 524(1)(b) and the restraint system is adjusted in accordance with the instructions referred to in paragraph 524(1)(c).
Belt buckles — mass-produced restraint systemsEvery belt buckle that is fitted on a belt designed to restrain a disabled person in a mass-produced restraint system for disabled persons mustunder the conditions set out in section 3 of Test Method 213.3,not release when any force of less than 40 N is applied, andrelease when a force of at least 40 N but not more than 62 N is applied;under the conditions set out in section 5 of Test Method 213.3, release when a force of not more than 71 N is applied;conform to the requirements of S4.3(d)(2) of TSD 209, except that the surface area of a belt buckle designed for push-button application must be at least 385 mm2;conform to the requirements of S4.3(g) of TSD 209; andnot release during the dynamic tests specified in section 4 of Test Method 213.3.SOR/2013-117, s. 24
Belt buckles — custom restraint systemsEvery belt buckle that is fitted on a belt designed to restrain a disabled person in a custom restraint system for a disabled person mustunder the conditions set out in section 6 of Test Method 213.3,not release when any force of less than 40 N is applied, andrelease when a force of at least 40 N but not more than 71 N is applied;conform to the requirements of S4.3(d)(2) of TSD 209, except that the surface area of a belt buckle designed for push-button application must be at least 385 mm2; andconform to the requirements of S4.3(g) of TSD 209.SOR/2013-117, s. 24
WebbingAny webbing that is designed to secure a restraint system for disabled persons to a user-ready tether anchorage or to a lower universal anchorage system, or to restrain a disabled person within the restraint system, mustwhen tested in accordance with S5.1(b) of TSD 209, before being tested for resistance to abrasion as specified in S5.1(d) or S5.3(c) of TSD 209, for resistance to light as specified in S5.1(e) of TSD 209 or for resistance to micro-organisms as specified in S5.1(f) of TSD 209, have a breaking strength ofat least 15 000 N, in the case of webbing designed to secure the restraint system to the user-ready tether anchorage or to the lower universal anchorage system, orat least 11 000 N, in the case of webbing designed to restrain a disabled person within the restraint system;when tested in accordance with S5.1(b) of TSD 209, after being tested for resistance to abrasion as specified in S5.1(d) or S5.3(c) of TSD 209, have a breaking strength of at least 75% of its initial breaking strength;conform to the requirements respecting breaking strength set out in S4.2(e) and (f) of TSD 209;in the case of a custom restraint system for a disabled person, have a width of not less than 38 mm, measured as specified in S5.1(a) of TSD 209, if contactable by the torso of a disabled person when the person is positioned in the restraint system; andin the case of a mass-produced restraint system for disabled persons, have a width of not less than 38 mm, measured as specified in S5.1(a) of TSD 209, if contactable by the torso of a disabled person when the person is positioned in the restraint system in accordance with the instructions referred to in paragraph 524(1)(b) and the restraint system is adjusted in accordance with the instructions referred to in paragraph 524(1)(c).SOR/2013-117, s. 20
Contactable Surfaces
Removable surfacesA surface of a restraint system for disabled persons that is placed in front of the disabled person must be removable when the restraint system is installed in a vehicle, unless the surface is designed to restrain the person.
Cross-sections of surfaceEvery horizontal cross-section of a surface of a restraint system for disabled persons that is designed to limit the forward movement of a disabled person must be flat or concave, and every vertical longitudinal cross-section of that surface must be flat or convex with a radius of curvature of the underlying structure of not less than 50 mm.
Rigid structural elementsAny rigid structural element underlying a contactable surface of a restraint system for disabled persons must not havea protrusion, with any padding or flexible overlay material removed, of more than 9.5 mm; oran exposed edge with a radius of less than 6.4 mm.
Surface contactable by head — custom restraint system for a disabled personEvery surface of a custom restraint system for a disabled person that is contactable by the head of a disabled person when the person is positioned in the restraint system must be covered with slow-recovery, energy-absorbing material that, when tested in accordance with section 7 of Test Method 213.3, hasa resistance of not less than 4 kPa but not more than 70 kPa at 25% of compression-deflection resistance;a thickness of not less than 12 mm, if the material has a resistance of not less than 12 kPa but not more than 70 kPa at 25% of compression-deflection resistance; anda thickness of not less than 19 mm, if the material has a resistance of not less than 4 kPa but less than 12 kPa at 25% of compression-deflection resistance.Surface contactable by head — mass-produced restraint system for disabled personsEvery surface of a mass-produced restraint system for disabled persons that is contactable by the head of a disabled person when the person is positioned in the restraint system in accordance with the instructions referred to in paragraph 524(1)(b) and the restraint system is adjusted in accordance with the instructions referred to in paragraph 524(1)(c) must be covered with slow-recovery, energy-absorbing material that, when tested in accordance with section 7 of Test Method 213.3, hasa resistance of not less than 4 kPa but not more than 70 kPa at 25% of compression-deflection resistance;a thickness of not less than 12 mm, if the material has a resistance of not less than 12 kPa but not more than 70 kPa at 25% of compression-deflection resistance; anda thickness of not less than 19 mm, if the material has a resistance of not less than 4 kPa but less than 12 kPa at 25% of compression-deflection resistance.
Testing
Inversion testingIf a restraint system for disabled persons is designed to be used in an aircraft, it must, when subjected to an inversion test in accordance with section 8 of Test Method 213.3, conform to the following requirements:the restraint system must not fall out of the aircraft passenger seat belt at any time during the rotation or three-second immobilization period referred to in that section; andthe anthropomorphic test device must not fall out of the restraint system at any time during the rotation or three-second immobilization period referred to in that section.
Dynamic testingA mass-produced restraint system for disabled persons that is subjected to a dynamic test in accordance with section 4 of Test Method 213.3 must, when in any adjustment position for which there is no warning under subparagraph 521(1)(f)(ii),exhibit no complete separation of any load-bearing structural element, and no partial separation exposing a surface witha protrusion of more than 9.5 mm, ora radius of less than 6.4 mm;remain in the same adjustment position during the test as it was in immediately before the test;except in the case of a restraint system tested with the anthropomorphic test device specified in subpart S, part 572, chapter V, title 49 of the Code of Federal Regulations of the United States (revised as of October 1, 2012), limit the resultant acceleration at the location of the accelerometer mounted in the upper thorax of the anthropomorphic test device to not more than 60 g, except for intervals of not more than 3 ms; andexcept in the case of a restraint system tested with the anthropomorphic test device specified in subpart S, part 572, chapter V, title 49 of the Code of Federal Regulations of the United States (revised as of October 1, 2012), limit the resultant acceleration of the centre of gravity of the head of the anthropomorphic test device during the movement of the head towards the front of the vehicle to not more than 80 g, except for intervals of not more than 3 ms, unless it is established that any resultant acceleration above 80 g is caused by another part of the anthropomorphic test device striking its head.Dynamic testing — levelling deviceA rear-facing mass-produced restraint system for disabled persons that is subjected to a dynamic test in accordance with section 4 of Test Method 213.3 must conform to the requirements of paragraphs (1)(a) and (b) if the restraint system is equipped with a levelling device andthe adjustment position of the levelling device is not in accordance with the manufacturer’s instructions; andthe other components of the restraint system are in any adjustment position for which there is no warning under subparagraph 521(1)(f)(ii).SOR/2013-117, s. 25
Forward-facing mass-produced restraint systemA forward-facing mass-produced restraint system for disabled persons that is subjected to a dynamic test in accordance with section 4 of Test Method 213.3 must not, when in any adjustment position for which there is no warning under subparagraph 521(1)(f)(ii),except in the case of a restraint system tested with the anthropomorphic test device specified in subpart S, part 572, chapter V, title 49 of the Code of Federal Regulations of the United States (revised as of October 1, 2012), allow any portion of the head of the anthropomorphic test device to pass through the vertical transverse plane — shown as the forward excursion limit in Figures 5 and 6 of Schedule 7 — that, measured along the SORL, is720 mm forward of the Z point on the standard seat assembly in the case of a restraint system designed to be used by a person whose mass is not more than 30 kg, and813 mm forward of the Z point on the standard seat assembly for a restraint system designed to be used by a person whose mass is more than 30 kg;except in the case of a restraint system tested with the anthropomorphic test device specified in subpart S, part 572, chapter V, title 49 of the Code of Federal Regulations of the United States (revised as of October 1, 2012), allow either knee pivot point to pass through the vertical transverse plane — shown as the forward excursion limit in Figures 5 and 6 of Schedule 7 — that is 915 mm forward of the Z point on the standard seat assembly, measured along the SORL; andallow the angle between the restraint system’s back support surface and seating surface to be less than 45° at the completion of the test.SOR/2013-117, s. 25
Rear-facing mass-produced restraint systemA rear-facing mass-produced restraint system for disabled persons that is subjected to a dynamic test in accordance with section 4 of Test Method 213.3 must, when in any adjustment position for which there is no warning under subparagraph 521(1)(f)(ii),retain the torso of the anthropomorphic test device within the restraint system, and not allow any portion of the target points on either side of the device’s head, located on the transverse axis passing through the centre of mass of the device’s head and perpendicular to the head’s midsagittal plane, to pass at any time, during or immediately after the test, either through the transverse orthogonal planes formed by the extension of the seat back frontal surface plane of the restraint system and by the plane that passes through the uppermost point of the restraint system, as shown in Figure 7 of Schedule 7, or through the vertical transverse plane passing through point X on the standard seat assembly, as shown in Figure 8 of Schedule 7; andnot allow the angle between the vertical and the back and head support surface, measured 240 mm above the seating surface, to be more than 70° at any time during the test.
Information
Information — mass-produced restraint systemsEvery mass-produced restraint system for disabled persons must have stitched onto it, indelibly moulded into or onto it, or indelibly printed on a label affixed to it in a permanent manner, the following information:the name and principal place of business of the company that manufactured, imported or sold the restraint system;the model name and number of the restraint system;the date of manufacture of the restraint system, as shown in Schedule 5, with the year, month and day above the corresponding wording in both official languages;a statement indicating — in units based on the International System of Units followed by the corresponding imperial units in parentheses — the mass and height range of the persons for whom the manufacturer recommends the restraint system when it is used in a forward-facing and, where applicable, a rear-facing position;a statement indicating whether the restraint system conforms to the inversion test requirements referred to in section 517;a warning indicatingthat the restraint system is designed for use by a disabled person,if the restraint system is not designed to be used at certain adjustment positions or with trays or tables or certain webbing assemblies, that those adjustment positions, trays, tables or webbing assemblies must not be used,if the restraint system is equipped with a lower connector system and is to be used by a disabled person with a mass of 30 kg or less, that the restraint system must be secured to the vehicle as shown in the installation instructions by either of the following means and, if the restraint system is equipped with a tether strap and the manufacturer recommends its use, by means of the tether strap:the lower connector system, if the restraint system is installed in a seating position that is equipped with a lower universal anchorage system, ora vehicle seat belt, if the restraint system is installed in a seating position that is not equipped with a lower universal anchorage system,if the restraint system is equipped with a lower connector system or a tether strap and is to be used by a disabled person with a mass of more than 30 kg, that the restraint system must be secured to the vehicle by means of a vehicle seat belt only,if the restraint system is not equipped with a lower connector system, that the restraint system must be secured to the vehicle as shown in the installation instruction by means of a vehicle seat belt and, if the restraint system is equipped with a tether strap and the manufacturer recommends its use, by means of the tether strap,if the restraint system is equipped with belts for restraining a disabled person, that the belts provided with the restraint system must be snugly adjusted around the person, andif the restraint system is equipped with a fixed or movable surface for restraining the disabled person and belts for restraining the disabled person, that the surface alone is not sufficient to restrain the person; andan installation diagram that shows the restraint systeminstalled as recommended by the manufacturer in a seating position that is equipped only with a lap belt and secured to the vehicle by means of the belt and, if the restraint system is equipped with a tether strap and the manufacturer recommends its use, by means of the tether strap,installed as recommended by the manufacturer in a seating position that is equipped only with a continuous-loop lap and shoulder belt, and secured to the vehicle by means of the belt and, if the restraint system is equipped with a tether strap and the manufacturer recommends its use, by means of the tether strap, andif the restraint system is equipped with a lower connector system, installed as recommended by the manufacturer in a seating position that is equipped with a lower universal anchorage system, and secured to the vehicle by means of the lower connector system and, if the restraint system is equipped with a tether strap and the manufacturer recommends its use, by means of the tether strap.Official languages and print sizeThe information referred to in subsection (1) must be in both official languages and in characters of at least 10 points, except for the words “year/année”, “month/mois” and “day/jour” under the date of manufacture, which may be in characters of at least 8 points.Visibility of informationThe information referred to in paragraphs (1)(d) to (g) must be fully visible at all times, even when the restraint system is occupied.
Warning — school busesEvery custom restraint system for a disabled person that is designed to be used only in school buses must bear the school bus restraint system warning label shown in Schedule 6, and the label must conform to the requirements of that schedule.IdemThe label referred to in subsection (1) must be affixed in a permanent manner and be fully visible.
Information — custom restraint systemsEvery custom restraint system for a disabled person must be accompanied by a document, in both official languages, that contains the following information:a statement that the restraint system must be used only by the person for whom the restraint system was designed;the name and principal place of business of the company that manufactured, imported or sold the restraint system;the date of manufacture of the restraint system, as shown in Schedule 5, with the year, month and day above the corresponding wording in both official languages;except in the case of a custom restraint system for a disabled person that is designed to be used only in school buses, a statement that the restraint system conforms to the prescribed standards applicable on the date of manufacture;a statement indicating whether the restraint system conforms to the inversion test requirements referred to in section 517;if the restraint system is designed to be used with a tether strap, a statement that the tether strap must be properly attached to the vehicle and indicating how to attach the tether strap;a warning indicatingif the restraint system is not designed to be used at certain adjustment positions or with trays or tables or certain webbing assemblies, that those adjustment positions, trays, tables or webbing assemblies must not be used,if the restraint system has a belt with a hook and loop fastener (for example, a Velcro-type fastener) that is designed to restrain a disabled person, that the fastener alone is not sufficient to restrain the disabled person, and that only belts that include buckles must be used to restrain the person, andif the restraint system is designed to restrain a disabled person by means of a fixed or movable surface and by means of belts, that the surface alone is not sufficient to restrain the person.
Installation instructionsEvery mass-produced restraint system for disabled persons must be accompanied by printed instructions, in both official languages, that set out a step-by-step procedure, including diagrams, forinstalling and securing the restraint system in a vehicle;positioning a disabled person in the restraint system; andadjusting every part of the restraint system that is designed to restrain the person.IdemThe instructions referred to in paragraph (1)(a) must state that the restraint system, even when unoccupied, must be firmly secured to the vehicle.IdemThe instructions mustspecify the classes of vehicles, the seating positions and the types of vehicle seat belts with which the restraint system may or may not be used;specify whether the restraint system may be used with a lower universal anchorage system;explain the primary consequences of not following the warnings appearing on the restraint system;if the restraint system conforms to the inversion test requirements of section 517, provide a step-by-step procedure, including diagrams, for installing the restraint system in an aircraft passenger seat referred to in subsection 2.1.2 of Test Method 213.3, for restraining a disabled person in the restraint system when it is installed in the seat, and for adjusting the restraint system to fit the person; andif the restraint system conforms to the inversion test requirements of section 517 and is manufactured with a removable base, and the seating component of the restraint system is designed to be used in a vehicle with or without the base, specify whether the restraint system must be used with or without the base in an aircraft passenger seat.Storage of instructionsEvery mass-produced restraint system for disabled persons must have a place for the storage of instructions.
[525 to 599 reserved]CMVSS 213.5 — Restraint Systems for Infants with Special NeedsGeneral
InterpretationIn this Part, Test Method 213.5 means Test Method 213.5 — Restraint Systems for Infants with Special Needs (May 2012), published by the Department of Transport.SOR/2013-117, s. 22
Restraint system designed to face the rearEvery restraint system for infants with special needs must be designed to face the rear of the vehicle, except that a car bed must be designed to rest on the vehicle’s rear bench seat so that its longitudinal axis is perpendicular to the vertical longitudinal plane passing through the longitudinal axis of the vehicle.
Torso restraintEvery restraint system for infants with special needs must, when the anthropomorphic test device is positioned in the restraint system in accordance with, in the case of a car bed, subsection 4.5.2 or 4.6.2 of Test Method 213.5 or, in the case of all other restraint systems for infants with special needs, subsection 4.5.3 or 4.6.3 of Test Method 213.5,restrain the upper torso by means of belts passing over each shoulder; andrestrain the lower torso.
Means of securing restraint systemSubject to subsection (2), every restraint system for infants with special needs must be designed to be secured to a vehicleby means of a vehicle seat belt in such a manner that the belt will not impose directly on the infant any loads that result from the mass of the restraint system, and without using any other means of attachment; andif the restraint system is equipped with a lower connector system, by means of the lower connector system, without using any other means of attachment.Restraint system with tether strapIf a restraint system for infants with special needs is equipped with a tether strap and the manufacturer recommends its use, the restraint system must be designed to be secured to a vehicleby means of the tether strap together with a vehicle seat belt in such a manner that the belt will not impose directly on the infant any loads that result from the mass of the restraint system, and without using any other means of attachment; andif the restraint system is equipped with a lower connector system, by means of the tether strap together with the lower connector system, without using any other means of attachment.
Restraint system with removable baseIf a restraint system for infants with special needs is equipped with a lower connector system and is manufactured with a removable base, and the seating component of the restraint system is designed to be used in a vehicle with or without the base, the restraint system must be equipped with the lower connector system on the base.
Car bedEvery car bed mustprovide restraint against the sideways movement of the infant’s head towards the front of the vehicle by means of a head restraint; andhave, in the shell of the car bed, a means of minimizing, when the car bed is installed in a vehicle in accordance with the manufacturer’s instructions, any loads to the top of the infant’s head in case of a side impact.
Restraint system to be adjustableEvery part of a restraint system for infants with special needs that is designed to restrain an infant must be adjustable to snugly fit an infant whose mass and height are within the ranges indicated in the statement referred to in paragraph 616(1)(d), when the infant is positioned in the restraint system in accordance with the instructions referred to in paragraph 618(1)(b) and the restraint system is adjusted in accordance with the instructions referred to in paragraph 618(1)(c).
Audible or visible indicationA restraint system for infants with special needs that is equipped with a lower connector system must provide a clear, audible indication when each connector in a lower connector system is securely attached to the lower universal anchorage system or a clear, visual indication that each connector is securely attached to the lower universal anchorage system.
FlammabilityEvery restraint system for infants with special needs must be constructed only of materials that conform to the requirements of TSD 302.SOR/2013-117, s. 23
Belt Buckles and Webbing
Conformity with TSD 209Every belt buckle and related piece of adjustment hardware and every tether strap attachment and related piece of adjustment hardware that are part of a restraint system for infants with special needs must conform to the requirements of S4.3(a)(2) and (b) of TSD 209.
Belt bucklesEvery belt buckle that is fitted on a belt designed to restrain an infant in a restraint system for infants with special needs mustunder the conditions set out in section 3 of Test Method 213.5,not release when any force of less than 40 N is applied, andrelease when a force of at least 40 N but not more than 62 N is applied;under the conditions set out in section 5 of Test Method 213.5, release when a force of not more than 71 N is applied;conform to the requirements of S4.3(d)(2) of TSD 209, except that the surface area of a belt buckle designed for push-button application must be at least 385 mm2;conform to the requirements of S4.3(g) of TSD 209; andnot release during the dynamic tests specified in section 4 of Test Method 213.5.SOR/2013-117, s. 24
WebbingAny webbing that is designed to secure a restraint system for infants with special needs to a user-ready tether anchorage or to a lower universal anchorage system, or to restrain an infant with special needs within the restraint system, mustwhen tested in accordance with S5.1(b) of TSD 209, before being tested for resistance to abrasion as specified in S5.1(d) or S5.3(c) of TSD 209, for resistance to light as specified in S5.1(e) of TSD 209 or for resistance to micro-organisms as specified in S5.1(f) of TSD 209, have a breaking strength ofat least 15 000 N, in the case of webbing designed to secure the restraint system to the user-ready tether anchorage or to the lower universal anchorage system, orat least 11 000 N, in the case of webbing designed to restrain an infant with special needs within the restraint system;when tested in accordance with S5.1(b) of TSD 209, after being tested for resistance to abrasion as specified in S5.1(d) or S5.3(c) of TSD 209, have a breaking strength of at least 75% of its initial breaking strength;conform to the requirements respecting breaking strength set out in S4.2(e) and (f) of TSD 209; andif contactable by the torso when the restraint system is tested in accordance with section 4 of Test Method 213.5, have a width of not less than 38 mm, measured as specified in S5.1(a) of TSD 209.SOR/2013-117, s. 21
Contactable Surfaces
Contactable surfacesEvery restraint system for infants with special needs, other than a car bed must providefor the support of the infant’s back, a continuous surface that is flat or concave and has an area of not less than 54 800 mm2; andfor the support of the sides of the infant’s torso, continuous surfaces that are flat or concave and have an area of not less than 30 500 mm2 each.Contactable surfaces — car bedEvery car bed must providefor the support of the infant’s back and legs, a continuous surface that is flat or concave and has an area of not less than 71 250 mm2; andfor the support of the sides of the infant’s torso and legs, continuous surfaces that are flat or concave and have an area of not less than 39 650 mm2 each.
Rigid structural elementsAny rigid structural element underlying a contactable surface of a restraint system for infants with special needs must not havea protrusion, with any padding or flexible overlay material removed, of more than 9.5 mm; oran exposed edge with a radius of less than 6.4 mm.
Surface contactable by headEvery surface of a restraint system for infants with special needs that is contactable by the head of an anthropomorphic test device positioned in the restraint system in accordance with, in the case of a car bed, subsection 4.5.2 or 4.6.2 of Test Method 213.5 or, in the case of all other restraint systems for infants with special needs, subsection 4.5.3 or 4.6.3 of Test Method 213.5 must be covered with slow-recovery, energy-absorbing material that, when tested in accordance with section 6 of Test Method 213.5, hasa resistance of not less than 4 kPa but not more than 70 kPa at 25% of compression-deflection resistance;a thickness of not less than 12 mm, if the material has a resistance of not less than 12 kPa but not more than 70 kPa at 25% of compression-deflection resistance; anda thickness of not less than 19 mm, if the material has a resistance of not less than 4 kPa but less than 12 kPa at 25% of compression-deflection resistance.
Testing
Dynamic testingA restraint system for infants with special needs that is subjected to a dynamic test in accordance with section 4 of Test Method 213.5 must, if the adjustment position of each component of the restraint system is in accordance with the manufacturer’s instructions,exhibit no complete separation of any load-bearing structural element, and no partial separation exposing a surface witha protrusion of more than 9.5 mm, ora radius of less than 6.4 mm;in the case of a restraint system other than a car bed, remain in the same adjustment position during the test as it was in immediately before the test began, except that, if the restraint system has a means of automatically repositioning the seating surface to allow the anthropomorphic test device to move from a reclined position to a more upright position and back to a reclined position during the test, the seating surface does not have to remain in the same adjustment position during the test as it was in immediately before the test began;in the case of a restraint system other than a car bed, retain the torso of the anthropomorphic test device within the restraint system, and not allow any portion of the target points on either side of the device’s head, located on the transverse axis passing through the centre of mass of the device’s head and perpendicular to the head’s midsagittal plane, to pass at any time, during or immediately after the test, through the transverse orthogonal planes formed by the extension of the seat back frontal surface plane of the restraint system and by the plane that passes through the uppermost point of the restraint system, as shown in Figure 7 of Schedule 7, or through the vertical transverse plane passing through point X on the standard seat assembly, as shown in Figure 8 of Schedule 7;in the case of a restraint system other than a car bed, not allow the angle between the vertical and the back and head support surface, measured 240 mm above the seating surface, to be more than 70° at any time during the test;in the case of a restraint system other than a car bed, limit the movement of the head of the anthropomorphic test device towards the rear of the restraint system by means of a continuous seat back that is an integral part of the restraint system;in the case of a restraint system other than a car bed, limit the rotation of the head of the anthropomorphic test device towards the rear of the restraint system, in its midsagittal plane, by means of a continuous seat back that is an integral part of the restraint system, so that the angle between the head and the torso is at no time during the test more than 45° as compared to the angle between the head and the torso prior to the test; andin the case of a car bed, retain the head, neck and torso of the anthropomorphic test device within the confines of the car bed.Dynamic testing — levelling deviceA restraint system for infants with special needs that is equipped with a levelling device and that is subjected to a dynamic test in accordance with section 4 of Test Method 213.5 must conform to the requirements of paragraphs (1)(a) and (b) if the adjustment position of each component of the restraint system, except the levelling device, is in accordance with the manufacturer’s instructions.Continuous seat backThe continuous seat back referred to in paragraphs (1)(e) and (f) musthave a height of at least 500 mm;have a width of at least 200 mm, measured in the horizontal plane at the height specified in paragraph (a); andnot impose any loads on the top of the head of the anthropomorphic test device during the dynamic test referred to in subsection (1).Measurement of height — paragraph 3(a)The height referred to in paragraph (3)(a) must be measured in a plane parallel to the surface of the seat back of the restraint system for infants with special needs and orthogonal to the vertical longitudinal plane passing through the longitudinal centreline of the restraint system, from the lowest point of the restraint system’s seating surface that is contacted by the buttocks of the seated anthropomorphic test device.ExceptionDespite paragraph (3)(b), if the restraint system for infants with special needs provides surfaces for the support of the sides of the torso, and those surfaces extend at least 100 mm forward from the padded surface of the portion of the restraint system provided for the support of the head of the anthropomorphic test device, the restraint system may have a continuous seat back width of not less than 150 mm, measured in the horizontal plane at the height specified in paragraph (3)(a).Restraint system with means of automatic repositioningIf a restraint system for infants with special needs that has a means of automatically repositioning the seating surface is subjected, in any adjustment position, to a dynamic test in accordance with section 4 of Test Method 213.5, an opening that is exposed and larger than 6.4 mm before the test must not become smaller during the test as a result of the movement of the seating surface relative to the other parts of the restraint system.
Information
InformationEvery restraint system for infants with special needs must have stitched onto it, indelibly moulded into or onto it, or indelibly printed on a label affixed to it in a permanent manner, the following information:the name and principal place of business of the company that manufactured, imported or sold the restraint system;the model name and number of the restraint system;the date of manufacture of the restraint system, as shown in Schedule 5, with the year, month and day above the corresponding wording in both official languages;a statement indicating — in units based on the International System of Units followed by the corresponding imperial units in parentheses — the mass and height range of the infants for whom the manufacturer recommends the restraint system;a warning indicatingthat the restraint system must be used only in a forward-facing seating position equipped with a vehicle seat belt or, if the restraint system is equipped with a lower connector system, in a forward-facing seating position equipped with a vehicle seat belt or a lower universal anchorage system,that the restraint system must be in a rear-facing position, except that a car bed must be used in a flat position along the vehicle’s rear bench seat with the head of the infant towards the centre of the vehicle,if the restraint system is equipped with a lower connector system, that the restraint system must be secured to the vehicle as shown in the installation instructions by either of the following means and, if the restraint system is equipped with a tether strap and the manufacturer recommends its use, by means of the tether strap:the lower connector system, if the restraint system is installed in a seating position that is equipped with a lower universal anchorage system, ora vehicle seat belt, if the restraint system is installed in a seating position that is not equipped with a lower universal anchorage system,if the restraint system is not equipped with a lower connector system, that the restraint system must be secured to the vehicle as shown in the installation instructions by means of a vehicle seat belt and, if the restraint system is equipped with a tether strap and the manufacturer recommends its use, by means of the tether strap, andif the restraint system is equipped with belts for restraining an infant, that the belts must be snugly adjusted around the infant; andan installation diagram that shows the restraint systeminstalled as recommended by the manufacturer in a seating position that is equipped only with a lap belt and secured to the vehicle by means of the belt and, if the restraint system is equipped with a tether strap and the manufacturer recommends its use, by means of the tether strap,installed as recommended by the manufacturer in a seating position that is equipped only with a continuous-loop lap and shoulder belt, and secured to the vehicle by means of the belt and, if the restraint system is equipped with a tether strap and the manufacturer recommends its use, by means of the tether strap, andif the restraint system is equipped with a lower connector system, installed as recommended by the manufacturer in a seating position that is equipped with a lower universal anchorage system, and secured to the vehicle by means of the lower connector system and, if the restraint system is equipped with a tether strap and the manufacturer recommends its use, by means of the tether strap.Official languages and print sizeThe information referred to in subsection (1) must be in both official languages and in characters of at least 10 points, except for the words “year/année”, “month/mois” and “day/jour” under the date of manufacture, which may be in characters of at least 8 points.Visibility of informationThe information referred to in paragraphs (1)(d) to (f) must be fully visible at all times, even when the restraint system is occupied, whether the restraint system is installed with or without a removable base.
Warning — air bagEvery restraint system for infants with special needs must bear the air bag warning label shown in Schedule 6, and the label must conform to the requirements of that schedule.IdemThe label referred to in subsection (1) must be affixed in a permanent manner at either of the following locations and be fully visible to a person installing the restraint system:on the side of the restraint system that will face the right front passenger door when the restraint system is facing rearward; orat the location where the infant’s head would rest or adjacent to that location.
Installation instructionsEvery restraint system for infants with special needs must be accompanied by printed instructions, in both official languages, that set out a step-by-step procedure, including diagrams, forinstalling and securing the restraint system in a vehicle;positioning an infant with special needs in the restraint system; andadjusting every part of the restraint system that is designed to restrain the infant.IdemThe instructions referred to in paragraph (1)(a) must state that the restraint system, even when unoccupied, must be firmly secured to the vehicle.IdemThe instructions mustspecify the classes of vehicles, the seating positions and the types of vehicle seat belts with which the restraint system may or may not be used;specify whether the restraint system may be used with a lower universal anchorage system;if the restraint system has a means of automatically repositioning the seating surface, specify that the ability of the restraint system to change position must not be impeded; andexplain the primary consequences of not following the warnings appearing on the restraint system.Storage of instructionsEvery restraint system for infants with special needs must have a place for the storage of instructions.
[619 to 699 reserved]Transitional Provision, Repeal and Coming into ForceTransitional Provision
ConformityUntil December 31, 2011, the restraint systems and booster seats referred to in these Regulations may, instead of conforming to the requirements of these Regulations, conform to the requirements of the Motor Vehicle Restraint Systems and Booster Cushions Safety Regulations as they read on the day before the day on which these Regulations came into force and as they were modified in their application by the Order Modifying the Operation of the Motor Vehicle Restraint Systems and Booster Cushions Safety Regulations and the Motor Vehicle Safety Regulations, which came into effect on May 1, 2009 and was published in the Canada Gazette, Part I, on May 9, 2009.SOR/2010-279, s. 1, err., Vol. 144, No. 26
Repeal
[Repeal]
Coming into Force
PublicationThese Regulations come into force on the day on which they are published in the Canada Gazette, Part II.[Note: Regulations in force May 12, 2010.]
(Subsection 101(1.1))Department of TransportMotor Vehicle Safety Act (section 3)Motor Vehicle Restraint Systems and Booster Seats Safety Regulations (subsection 101(1.1))Ministerial AuthorizationUnder the Motor Vehicle Safety Act and the Motor Vehicle Restraint Systems and Booster Seats Safety Regulations,[company name and address]is authorized to apply the national safety mark to any restraint system or booster seat of a prescribed class referred to in section 102 of the Motor Vehicle Restraint Systems and Booster Seats Safety Regulations, on the condition that the restraint system or booster seat conforms to all of the applicable Canada Motor Vehicle Safety Standards.The national safety mark must be applied at the following premises:[address of the premises]This ministerial authorization (number ) expires on Issued in Ottawa on , 20for the Minister of TransportSOR/2020-22, s. 21(Subsections 101(1) and (3))NATIONAL SAFETY MARKSymbol showing the National Safety Mark consisting of an outline of a circle with CANADA NSVAC XXXX TRANSPORT CMVSS XXXX written along the inside rim of the circle with the outline of a maple leaf in the middle with YYY in the middle.Note: Replace XXXX with one or more of the following numbers, as applicable: 213, 213.1, 213.2, 213.3 and 213.5.Replace YYY with the authorization number assigned by the Minister.SOR/2020-22, s. 22(Section 105)LOWER UNIVERSAL ANCHORAGE SYSTEM SYMBOLLower Universal Anchorage System Symbol consisting of a black circle with a drawing of a child in a child restraint in the middle.[Repealed, SOR/2020-22, s. 23](Paragraphs 218(1)(c), 316(1)(c), 409(1)(c), 521(1)(c), 523(c) and 616(1)(c))DATE OF MANUFACTURE########year/annéemonth/moisday/jour
(Subsections 219(1), 317(1), 522(1) and 617(1))AIR BAG WARNING LABELWarning label with descriptions showing an airbag deploying onto a child in a rear-facing seat with a diagonal line across.Warning label with descriptions showing a person sitting behind another person wearing a restraint on a school bus with a diagonal line across.Requirements:The message area containing the warning statement must be at least 30 cm2The warning statement must be in characters of at least 10 pointsThe pictogram must be at least 30 mm in diameterNote: Drawings not to scale
SCHOOL BUS RESTRAINT SYSTEM WARNING LABEL
(Subsection 100(1), paragraphs 216(1)(a) and (b), 217(a), 315(1)(e), 407(e) and (f), 519(a) and (b), 520(a) and 615(1)(c))Diagram of Interface Profile of Tether Strap Hook with measurements and specifications.Notes:Dimensions in mm, except where otherwise indicatedDrawing not to scale
Figure 1 — Interface Profile of Tether Strap Hook
Diagram of Interface Profile of Tether Strap Hook with Integrated Adjustment Hardware with measurements and specifications.Notes:Dimensions in mm, except where otherwise indicatedDrawing not to scale
Figure 2 — Interface Profile of Tether Strap Hook with Integrated Adjustment Hardware
Diagram of Three-dimensional Schematic View of Standard Seat Assembly Indicating Location of Seat Belt Anchorage Points with measurements and specifications.Notes:Dimensions in mm, except where otherwise indicatedDrawing not to scaleLap belt anchorage points and continuous-loop lap and shoulder belt lower anchorage points are symmetrically located with respect to the SORL
Figure 3 — Three-dimensional Schematic View of Standard Seat Assembly Indicating Location of Seat Belt Anchorage Points
Diagram of Three-dimensional Schematic View of Standard Seat Assembly Indicating Location of Lower Universal Anchorage System with specifications.Notes:Drawing not to scaleTransverse horizontal distance between the centre of the bars and the vertical plane containing the SORL is 140 mm
Figure 4 — Three-dimensional Schematic View of Standard Seat Assembly Indicating Location of Lower Universal Anchorage System
Diagram of Side View of Standard Seat Assembly Indicating Location of Seat Belt Anchorage Points with measurements and specifications.Notes:Dimensions in mm, except where otherwise indicatedDrawing not to scaleUser-ready tether anchorage point on rear package shelf located on the vertical longitudinal plane containing the SORL or located 544 mm right or left of the vertical longitudinal plane containing the SORL
Figure 5 — Side View of Standard Seat Assembly Indicating Location of Seat Belt Anchorage Points
Diagram of Side View of Standard Seat Assembly Indicating Location of Lower Universal Anchorage System with measurements and specifications.Notes:Dimensions in mm, except where otherwise indicatedDrawing not to scaleUser-ready tether anchorage point on rear package shelf located on the vertical longitudinal plane containing the SORL or located 544 mm right or left of the vertical longitudinal plane containing the SORLLower universal anchorage system bars located 102 mm forward of the Z point and 323 mm upward from floor
Figure 6 — Side View of Standard Seat Assembly Indicating Location of Lower Universal Anchorage System
Diagram of Forward and Upper Excursion Limits for any Portion of Target Point on Either Side of Anthropomorphic Test Device Head with measurements and specifications.Note: The illustrated limits move during dynamic testing
Figure 7 — Forward and Upper Excursion Limits for any Portion of Target Point on Either Side of Anthropomorphic Test Device Head
Figure 8 — Point X on Vertical Plane of Standard Seat AssemblyDiagram of Point X on Vertical Plane of Standard Seat Assembly with specifications.Diagram of Rear and Side View of Checking Device for Lower Connector System - Envelope Dimensions with measurements and specifications.Notes:Dimensions in mm, except where otherwise indicatedDrawing not to scale
Figure 9 — Rear and Side View of Checking Device for Lower Connector System - Envelope Dimensions
RELATED PROVISIONS — SOR/2010-152, s. 13, as amended by SOR/2012-191, s. 44
Until December 31, 2011, the children’s car seats referred to in the Deduction for Provincial Rebate (GST/HST) Regulations, as amended by sections 9 to 11, may, instead of conforming to the requirements of the Motor Vehicle Restraint Systems and Booster Seats Safety Regulations, conform to the requirements of the Motor Vehicle Restraint Systems and Booster Cushions Safety Regulations as they read on May 11, 2010 and as they were modified in their application by the Order Modifying the Operation of the Motor Vehicle Restraint Systems and Booster Cushions Safety Regulations and the Motor Vehicle Safety Regulations, which came into effect on May 1, 2009 and was published in the Canada Gazette, Part I, on May 9, 2009.
SOR/2024-2742025-01-01SOR/2020-222020-02-04SOR/2019-2532019-07-10